Site Search Results

Global

Global Navigation

Home>
Site Search Results

Primary Contents

Search Guide

Site Search

Product Search

IA Global Search

Results 1141 - 1150 of 1189

CSM_VAQ_DS_E_4_9 1 Pushbutton Switch (Cylindrical ...: ...t touch the terminals or other charged parts of the Switch while power is being supplied. Doing so may result in electric shock. •After wiring the Switch, ensure an appropriate insulating dis...
https://www.ia.omron.com/data_pdf/cat/vaq_ds_e_4_9_csm613.pdf
CSM_VB_DS_E_1_4 1 Multiple Limit Switch VB: ...efully connect a conduit to each conduit hole and apply a seal or tape to seal the conduit hole so that cuttings or other materials will not penetrate through the conduit hole. •Use the SC Co...
https://www.ia.omron.com/data_pdf/cat/vb_ds_e_1_4_csm2175.pdf
CSM_VE_DS_E_2_2 1 Small Enclosed Switches: ...Tightening Torque If screws are too loose, they can lead to an early malfunction of the Switch, so ensure that all screws are tightened using the correct torque. Mounting Hole Dimensions Oper...
https://www.ia.omron.com/data_pdf/cat/ve_ds_e_2_2_csm589.pdf
Ultra-High Performance Intelligent Barcode Reader: ...mplex jobs from minutes to seconds •Tools arranged in reading order •ROIs (Regions of Interest) so each code can be read uniquely •ROI sized to accommodate the expected positional uncertainty...
https://www.ia.omron.com/data_pdf/cat/vhv5-f_q358-e_1_1_csm1132108.pdf
Vibration Suppression Library Sysmac Library for N...: ...20 x 20 = 400 chips per pallet Resonance frequency of pallet: 30 Hz The XY stage moves a pallet so that the vision sensor can inspect chips one by one. ApplicationHandling time per pallet: 42...
https://www.ia.omron.com/data_pdf/cat/vibration_suppression_library_p099-e1_2_4_csm1047444.pdf
General-purpose Switches Environment-resistant Swi...: ...th SPST-NO+NC contact form Roller Lever Bolt Set Position Marker Plate Set the indicator needle so that it is between protrusions on the bearing section on the marker plate after operation. R...
https://www.ia.omron.com/data_pdf/cat/wl-n_wlg_c151-e1_4_4_csm1057870.pdf
CSM_WL_DS_E_19_8 1 Two-circuit Limit Switch WL: ...epoxy resin to increase the seal. The cover cannot be removed. The SC connector can be removed, so it is possible to use flexible conduits for the cable. To prevent spatter during welding, a ...
https://www.ia.omron.com/data_pdf/cat/wl_ds_e_19_8_csm582.pdf
CSM_X_DS_E_4_4 1 General-purpose Basic Switch X: ... not use both the M12 mounting screw and the mounting holes in the case at the same time. Doing so will cause stress to be applied to the Switch, possibly damaging the case or cover. Panel Mo...
https://www.ia.omron.com/data_pdf/cat/x_ds_e_4_4_csm570.pdf
CSM_XS2_DS_E_12_10 1 Round Water-resistant Connect...: ...are identical to the connector pin numbers. •Tentatively insert the pins to the pin block holes so that the key on the pin block will coincide with the key groove on the pin clamp. Then inser...
https://www.ia.omron.com/data_pdf/cat/xs2_ds_e_12_10_csm1342.pdf
CSM_XS5_DS_E_14_6 1 Round Water-resistant Connecto...: ...has completed, mark of cap comes into the square of the indicator formed into a mold cover ( ), so also use it as guideline to know to complete. 2.Avoid tightening a cap up beyond the complet...
https://www.ia.omron.com/data_pdf/cat/xs5_ds_e_14_6_csm1340.pdf

Results 1141 - 1150 of 1189

Search Guide