Site Search Results

Global

Global Navigation

Home>
Site Search Results

Primary Contents

Search Guide

Site Search

Product Search

IA Global Search

Results 801 - 810 of 1186

CSM_D4C_DS_E_11_9 1 Enclosed Switch D4C: ...on of excess force on the cable. When bending the cable, provide a bending radius of 45 mm min. so as not to damage the cable insulation or sheath. Excessive bending may cause fire or leakage...
https://www.ia.omron.com/data_pdf/cat/d4c_ds_e_11_9_csm580.pdf
CSM_D4CC_DS_E_3_5 1 Miniature Limit Switch D4CC: ...ximum of 6 Switches may be group-mounted. In this case, pay attention to the mounting direction so that the convex part of the group-mounting guide on one Switch fits into the concave part of...
https://www.ia.omron.com/data_pdf/cat/d4cc_ds_e_3_5_csm581.pdf
CSM_D4E-_N_DS_E_6_6 1 Small Sealed Switch D4E-@N: ... •If the one-touch connector is to be mounted onto the switch body, lightly push up the fitting so that the switch body can then be inserted into the clamp. •Be sure that the clamp is inserte...
https://www.ia.omron.com/data_pdf/cat/d4e-_n_ds_e_6_6_csm585.pdf
CSM_D4F_DS_E_5_7 1 Small Safety Limit Switch D4F: ... D4F side-by-side. •Do not switch circuits for two or more standard loads (125 VAC, 1 A). Doing so may adversely affect insulation performance. Handling of Cables •Cables cannot be flexed rep...
https://www.ia.omron.com/data_pdf/cat/d4f_ds_e_5_7_csm1249.pdf
CSM_D4GS-N_DS_E_7_7 1 Slim Safety Door Switch D4GS...: ...R≥50) * Note 1: When determining the operation key insertion radius, adjust the adjusting screw so that the tip of the operation key is positioned to the center of the key insertion hole of t...
https://www.ia.omron.com/data_pdf/cat/d4gs-n_ds_e_7_7_csm1236.pdf
CSM_D4JL_D4JL-SK40_DS_E_10_7 1 Guard Lock Safety-d...: ...dition monitoring of Safety-door Switch Note: The lock release enable signal must be configured so that it should turn ON after dangerous movement is stopped and safety is ensured for the doo...
https://www.ia.omron.com/data_pdf/cat/d4jl_d4jl-sk40_ds_e_10_7_csm1239.pdf
CSM_D4MC_DS_E_2_7 1 Enclosed Switch D4MC: ... and apply a force in the opening direction. Do not use excess force to remove the cover. Doing so may cause deformation in the fitting section and reduce the holding force. •When mounting th...
https://www.ia.omron.com/data_pdf/cat/d4mc_ds_e_2_7_csm588.pdf
CSM_D4N-_R_DS_E_6_8 1 Pull-reset Safety Limit Swit...: ... been used to switch a standard load, it cannot be used for a load of a smaller capacity. Doing so may result in roughening of the contact surface and contact reliability may be lost. *1.The ...
https://www.ia.omron.com/data_pdf/cat/d4n-_r_ds_e_6_8_csm1252.pdf
CSM_D4N_DS_E_10_10 1 Safety Limit Switch D4N: ... been used to switch a standard load, it cannot be used for a load of a smaller capacity. Doing so may result in roughening of the contact surface and contact reliability may be lost. *1.The ...
https://www.ia.omron.com/data_pdf/cat/d4n_ds_e_10_10_csm1248.pdf
CSM_D4NH_DS_E_7_6 1 Safety-door Hinge Switch D4NH: ...re according to EN60947-5-1. 2. MBB (Make Before Break) contacts have an overlapping structure, so that before the normally closed contact (NC) opens, the normally open contact (NO) closes. *...
https://www.ia.omron.com/data_pdf/cat/d4nh_ds_e_7_6_csm1242.pdf

Results 801 - 810 of 1186

Search Guide