...equency, and the types of oscillators are determined depending on the required operating range. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01271/

...an the rated sensing distance, the operation in this kind of environment cannot be recommended. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01275/

...cable for the E4C-TS50S.) For the E4R, use an 11/0.16-dia. parallel 1-conductor shielded cable. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01281/

...pagation area of the ultrasonic waves, the cover will be detected, and thus it affects sensing. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01295/

... 5 poles. If this is done, however, you cannot use the mutual interference prevention function. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01335/

...non-uniform steams cause difference in temperature and therefore measurement error is observed. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01346/

...on from any object (even human bodies) is well transmitted so detection of that object is easy. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01359/

...e detected. When there is a background object in the red zone, the background will be detected. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01372/

...ance. For a Reflective Sensor, if this continues for a long time, detection becomes impossible. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01374/

...e Sensors are placed at different detection distances, and their sensing ranges do not overlap. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01408/

...the ultrasonic waves of adjacent Ultrasonic Sensors affect the outputs and makes them unstable. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What is the highest...

https://www.ia.omron.com/support/faq/answer/50/faq01432/

...sparent objects) Detecting edge positions (including transparent objects) Determining pin pitch E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq00471/

...d cables (shield specifications for the Amplifier Unit: 0.1 mm in diameter, 51 shielded wires). E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq00473/

...ot allowed. Remedy 2: Make the hysteresis value smaller to avoid the condition described above. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq00502/

... by going to FUN mode and setting (ZRMEN) under (SPCL) to (OFF). Actual indications on a panel. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq00505/

... distances. If they have different measurement distances, the correct distance cannot be found. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq00507/

...nels 1 and 2. The resolution on the channel 1 Amplifier shows the resolution of only channel 1. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq00514/

...d when performing calculations for adjacent Sensors? Answer  Up to 2 Sensors can be connected. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq00518/

...s it is for round bars. Averaging Small Irregularities on a Rough Surface: Easy Beam Alignment: E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq01186/

...ll the HIGH, PASS, and LOW judgment outputs? Answer  No, it is valid only for the PASS output. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions Support Software "S...

https://www.ia.omron.com/support/faq/answer/56/faq01204/