... do not require lines to be secured with screws as with previous connectors. Push up the orange lever and then insert each line into the back of each hole. Release the orange lever a...

https://www.omron-ap.co.in/data_pdf/mnu/w267-e1-13_devicenet.pdf

...Backplane. 2. Insert the ASCII Unit connector into the Backplane connector. Hook Backplane Lock lever Note When removing the ASCII Unit, lift it out while pressing down on the lock ...

https://www.omron-ap.co.in/data_pdf/mnu/w306-03_c200h-asc11_21_31.pdf

...sole. Contrast control Buzzer Volume The C200H-PRO27-E’s buzzer volume can be adjusted with the lever on the right side of the Programming Console. The CQM1-PRO01-E’s buzzer volume cannot be ...

https://www.omron-ap.co.in/data_pdf/mnu/w317-e1-11_cpm1a.pdf

... Volume With the C200H-PRO27-E Programming Console, the buzzer volume can be adjusted using the lever on the right-hand side of the Console. The CQM1HPRO01-E and CQM1-PRO01-E does not have bu...

https://www.omron-ap.co.in/data_pdf/mnu/w341-e1-05_c200h_cqm1_pro.pdf

...o the I/ O connector on the Slave until it clicks into place. Disconnecting Lift up on the lock lever as shown in the following diagram and remove the Cable Connector to disconnect it. L...

https://www.omron-ap.co.in/data_pdf/mnu/w347-e1-06_c200hw_cqm1-drt_drt1.pdf

...utions on Removable Terminal Blocks 8 The terminal block can be removed by pressing down on the lever at the bottom of the terminal block. Always confirm that this lever is up in the...

https://www.omron-ap.co.in/data_pdf/mnu/w396-e1-03_cj1w_tc.pdf

...nnector Plug components Black Cable labels (Flat cable: black, blue/green, white, and red) Lock lever 1. Cutting the Cable At the tip of the cable, cut the cable perpendicular to the cable le...

https://www.omron-ap.co.in/data_pdf/mnu/w485-e1-03_3g8f7-crm21_3g8f8-crm21.pdf

...D081 O N O N ON MODE 1 2 1 2 1 2 MODE Terminal block DIN Track mounting pin Terminal block lock lever (pull down to release terminal block) Operating mode switch z Side Slider Expansion conne...

https://www.omron-ap.co.in/data_pdf/mnu/w490-e1-03_cj1w-ad0__-___da0_mad42.pdf

...cautions on Removable Terminal Blocks The terminal block can be removed by pressing down on the lever at the bottom of the terminal block. Always confirm that this lever is up in the...

https://www.omron-ap.co.in/data_pdf/mnu/w491-e1-03_cj1w-tc003_004_103_104.pdf

...ector Plugs • Component Names Cable labels (Flat cable: black, blue/green, white, and red) Lock lever 1 Cutting the Cable Cut the cable perpendicular to the length. To prevent short-circuits,...

https://www.omron-ap.co.in/data_pdf/mnu/w493-e1-03_cj1w-crm21.pdf

...nal block. Doing so may damage the terminal block. 7 Removing a Terminal Block 1 Press the lock lever on the terminal block and pull out the top of the terminal block to remove it. NX-series ...

https://www.omron-ap.co.in/data_pdf/mnu/w519-e1-18_nx-ecc20_.pdf

...it. (G) Screw terminals These screw terminals are used to connect the wires. (H) Terminal block lever This lever is used to fix the terminal block on the NX Unit. (I) Unit specificat...

https://www.omron-ap.co.in/data_pdf/mnu/w521-e1-13_nx-id_ia_oc_od_md.pdf

... Doing so may damage the terminal block. NG OK NG NG 4 Removing a Terminal Block Press the lock lever on the terminal block and pull out the top of the terminal block to remove it. Lock ...

https://www.omron-ap.co.in/data_pdf/mnu/w522-e1-11_nx-ad_da.pdf

...d the cable forcibly. Doing so may break the cables. Removing a Terminal Block 1 Press the lock lever on the terminal block and pull out the top of the terminal block to remove it. Lock ...

https://www.omron-ap.co.in/data_pdf/mnu/w523-e1-11_nx-pd1_pf0_pc0_tbx01.pdf

...lease hole. Doing so may break the terminal block. 7 Removing a Terminal Block 1 Press the lock lever on the terminal block and pull out the top of the terminal block to remove it. Lock ...

https://www.omron-ap.co.in/data_pdf/mnu/w536-e1-11_nx-eic202.pdf

... cable forcibly. Doing so may break the cables. Removing a Terminal Block 1 4-12 Press the lock lever on the terminal block and pull out the top of the terminal block to remove it. NX-series ...

https://www.omron-ap.co.in/data_pdf/mnu/w540-e1-09_nx-cif.pdf

...o install a drive: 1 Ensure the Box PC is OFF. 2 Remove the drive cover. 2 3 1 1) Push the lock lever 1 . 2) Tilt the drive cover 2 . 3) Remove the drive cover 3 . 5-6 NY-series NYB Industria...

https://www.omron-ap.co.in/data_pdf/mnu/w553-e2-16_nyb.pdf

...install a drive: 1 Ensure the Panel PC is OFF. 2 Remove the drive cover. 2 3 1 1) Push the lock lever 1 . 2) Tilt the drive cover 2 . 3) Remove the drive cover 3 . 5-4 NY-series NYP Industria...

https://www.omron-ap.co.in/data_pdf/mnu/w555-e2-16_nyp.pdf

...o install a drive: 1 Ensure the Box PC is OFF. 2 Remove the drive cover. 2 3 1 1) Push the lock lever 1 . 2) Tilt the drive cover 2 . 3) Remove the drive cover 3 . NY-series Industrial Box PC...

https://www.omron-ap.co.in/data_pdf/mnu/w556-e2-08_ny512-1_00.pdf

... Doing so may damage the terminal block. NG OK NG NG 4 Removing a Terminal Block Press the lock lever on the terminal block and pull out the top of the terminal block to remove it. Lock ...

https://www.omron-ap.co.in/data_pdf/mnu/w565-e1-06_nx-rs.pdf