Site Search | Product Search | IA Global Search |
... wiring reduces disconnection risk and avoids noise sources. Optical synchronization Smartclick cable connection for fast set-up No torque-control required: the Smartclick connectors connect ...
... power source, connect both ends of the command pulse signal line shield (shielded twisted-pair cable) to the frame ground. Note: Make sure that the Controller and the Driver are always groun...
...resistor or the Terminal Block style terminating resistor DRST-1 must be connected. The maximum cable length between the node and the terminating resistor is 1m. CJ2 Introducing the Flagship ...
...DeviceNet? Is it acceptable to combine SRT1 Slaves and SRT2 Slaves in a CompoBus/S system? What cable lengths are sold for the cables used to wire the network between DeviceNet Master Units a...
...dels with directly attached connectors and models with pre-wired connectors are available. XS2F Cable is used to connect to models with directly attached connectors and models with pre-wired ...
...s not self-holding because of a disconnection or poor contact between the E2' electrode and its cable. Countermeasures 1.Momentarily short the E1' and E3 terminals of the 61F-G1 Controller to...
...pecifications will not be met. To reduce the effects of noise, use a special E69-DF[] Extension Cable. Do not relay the cable using a terminal block. Doing so will cause the signal t...
...rpose Limit switches Actuator Roller plunger Electrical ratings 1 A at 30 VDC Contact form SPDT Cable specifications Oil-resistant cable, 3 cores, 0.3 m Degree of protection IP67 Ite...
...purpose Limit switches Actuator Roller lever Electrical ratings 1 A at 30 VDC Contact form SPDT Cable specifications Oil-resistant cable, 3 cores, 0.3 m Degree of protection IP67 Ite...
...hing capacity) 100 mA max. Control output (Residual voltage) 2 V max. (Load current 100 mA with cable length of 2 m) Indicator Operation indicator (yellow) Operation mode NO Protective circui...
...tching capacity) 3 to 50 mA Control output (Residual voltage) 3 V max. (Load current 50 mA with cable length of 2 m) Indicator Operation indicator (red), Operation setting indicator (green) O...
...tching capacity) 3 to 50 mA Control output (Residual voltage) 5 V max. (Load current 50 mA with cable length of 2 m) Indicator Operation indicator (red), Operation setting indicator (green) O...
...hing capacity) 100 mA max. Control output (Residual voltage) 2 V max. (Load current 100 mA with cable length of 2 m) Indicator Operation indicator (yellow) Operation mode NO Protective circui...
...16L) Sensing surface: Polybutylene terephthalate (PBT) Clamping nuts: Stainless steel (SUS316L) Cable: Heat-resistant PVC cable Accessories Instruction manual As of August 8, 2024 Di...
...hing capacity) 100 mA max. Control output (Residual voltage) 2 V max. (Load current 100 mA with cable length of 2 m) Indicator Operation indicator (yellow) Operation mode NO Protective circui...
...hing capacity) 100 mA max. Control output (Residual voltage) 2 V max. (Load current 100 mA with cable length of 2 m) Indicator Operation indicator (yellow) Operation mode NC Protective circui...
...hing capacity) 100 mA max. Control output (Residual voltage) 2 V max. (Load current 100 mA with cable length of 2 m) Indicator Operation indicator (yellow) Operation mode NC Protective circui...
...hing capacity) 100 mA max. Control output (Residual voltage) 2 V max. (Load current 100 mA with cable length of 2 m) Indicator Operation indicator (yellow) Operation mode NO Protective circui...
...16L) Sensing surface: Polybutylene terephthalate (PBT) Clamping nuts: Stainless steel (SUS316L) Cable: Heat-resistant PVC cable Accessories Instruction manual As of August 8, 2024 Di...
...hing capacity) 100 mA max. Control output (Residual voltage) 2 V max. (Load current 100 mA with cable length of 2 m) Indicator Operation indicator (yellow) Operation mode NO Protective circui...