...il it clicks. When the power button is pressed, laser is radiated. 4. Perform coarse adjustment so that laser beam is radiated at the center of the top of the opposed receiver (or emitter). A...

https://www.fa.omron.com.cn/data_pdf/mnu/f39-ptr_-ptj_inst-2132523-0i.pdf

...t use the product in areas where flammable or explosive gases are present. •Install the product so that air can flow freely through its cooling vents. •Clean the ventilation holes and fan out...

https://www.fa.omron.com.cn/data_pdf/mnu/fh-2____(-__)_fh-5___(-__)_inst-3102269-4b.pdf

...s the electric shock and a fire. Do not touch the terminals while the power supply is ON. Doing so may result in electrical shock. Never disassemble, apply pressure that would deform, or inci...

https://www.fa.omron.com.cn/data_pdf/mnu/fh-mt12_inst-5359165-0c.pdf

...als. [Note] Do not grab the cable and pull it out with a unreasonable force to remove it. Doing so might cause breakage. [Important] Do not touch the internal terminals of the connector. Doin...

https://www.fa.omron.com.cn/data_pdf/mnu/fl-md_mc_inst-3125822-1d.pdf

...able [NOTE] Do not grab the cable and pull it out with a unreasonable force to remove it. Doing so might cause breakage. [IMPORTANT] - Do not touch the internal terminals of the connector. Do...

https://www.fa.omron.com.cn/data_pdf/mnu/fl-tcc1ps_inst-3127062-0d.pdf

...andling ·Do not peel off or damage the waterproof sheet attached to the side of the unit. Doing so may result in dirt, dust or water droplet entering inside the device, causing a failure of t...

https://www.fa.omron.com.cn/data_pdf/mnu/fq-cr__inst-2243166-2h.pdf

...of the camera and the camera connector on Controller FZ series. *The camera cable is polarized, so, make sure that the end bearing a name plate is connected to the Controller . PRECAUTIONS FO...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-sc2m_s2m_inst-2269008-0b.pdf

...7 9.5 9.5 15.5 10 2-M4深さ5.5 1/4" 20UNC深さ5.52-Ø4.519±0.1 取付穴加工寸法 *The camera cable is polarized, so, mak e sure that the end bearing a name plate is connected to the Controller . *W...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-sc5m3_s5m3_inst-3126677-1a.pdf

... INSPECTION SYSTEM General specifications *The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so, make sure that the end bearing a name plate is connected to the controller . (1) The camera...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-sc_s_inst-9066829-8a.pdf

...l: (49) 7032-811-0/Fax: (49) 7032-811-199 Regional Headquarters *The camera cable is polarized, so, make sure that the end bearing a name plate is connected to the Controller....

https://www.fa.omron.com.cn/data_pdf/mnu/fz-sfc_sf_spc_sp_inst-0185689-2c.pdf

...camera connector on Controller FZ series. *The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so, make sure that the end bearing a name plate is connected to the Controller .1“-32UNF(C MOUN...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-shc_sh_inst-2135165-7a.pdf

...ffusion Board is installed. 1. Loosen the screws of the mounting brackets and turn the brackets so that they will not catch on the illumination part of the FZ-SLC100. 2. Place the Diffusion B...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-slc100-dl_inst-1652061-0a.pdf

...power equipment. PRECAUTIONS FOR SAFE USE *The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so, make sure that the end bearing a name plate is connected to the controller . Thank you for ...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-slc100_inst-1636848-7d.pdf

...en the screws of the mounting brackets with the provided hexagonal wrench and turn the brackets so that they will not catch on the illumination part of the FZ-SLC15. 2. Place the Diffusion Bo...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-slc15-dl_inst-9442174-2a.pdf

...d the camera connector on Controller FZ□. *The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so, make sure that the end bearing a name plate is connected to the controller . Thank you for ...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-slc15_inst-1652099-8c.pdf

... camera connector on Controller FZseries. ※The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so, make sure that the end bearing a nameplate is connected to the Controller FZseries. PRECAUT...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-szc100_inst-1641749-6a.pdf

... camera connector on Controller FZseries. ※The camera cable (FZ-VS,FZ-VSL,FZ-VSB) is polarized, so, make sure that the end bearing a nameplate is connected to the Controller FZseries. PRECAUT...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-szc15_inst-0994985-7a.pdf

... is necessary to supply an external power supply by the direct current voltage product designed so as not to generate a high voltage (safety extra low voltage circuit). ・Reverse connection o...

https://www.fa.omron.com.cn/data_pdf/mnu/fz-vsj_inst-9470198-2g.pdf

.../E台反E诺台指反迟绝连4/3绝/E异规格型致9SX-读S是根据规格要求，设计/制造的产品反反反反反反反反反E读反件SO连3以49-连:迟绝连5 反反反反全等3反国对反d反(使用型D4绝问时取, 反反反全等4反国对反e反(使...

https://www.fa.omron.com.cn/data_pdf/mnu/g9sx-nsa222-t03-__ns202-___inst-2166130-3c.pdf

... understand this manual in order to ensure correct use. Also, store this manual in a safe place so that it can be accessed whenever necessary. In this manual, current output models (E5ZN-2C@F...

https://www.fa.omron.com.cn/data_pdf/mnu/h113-e1-04_e5zn.pdf