GlobalIA Global Search Results
| Site Search | Product Search | IA Global Search |
previous
FAQ00680 for Servomotors / Servo Drivers | OMRON I......alog monitor output? Answer Yes, there is a cable available. The Analog Monitor Cable for the W-series (R88D-W) Servo Drivers can be used. The Cable's model number is R88A-CMW001S....
- FAQ02569 for Servomotors / Servo Drivers | OMRON I...
...control is possible by installing a DeviceNet Communications Unit (R88A-NCW152-DRT) in an OMNUC W-series Servo Driver. A DeviceNet Communications Unit provides a DeviceNet communications inte...
- FAQ02058 for Solid-state Relays | OMRON Industrial...
...turned ON. This is more clearly checked if the dummy load is a lamp with an output of about 100 W. (However, the capacity of the lamp must be within the rated range of the SSR.) MY Best-selli...
- FAQ02152 for Solid-state Relays | OMRON Industrial...
...ds can be directly switched without bleeder resistance. Bleeder Resistance 100 VAC 5 to 10 kΩ 3 W 200 VAC 5 to 10 kΩ 15 W Solid-state Relays with DC Output: Leakage current may cause...
- FAQ02155 for Solid-state Relays | OMRON Industrial...
...tor must be checked to match the load, but previous experience shows that a resistor of 100 Ω/1 W and a capacitor of 0.1 μF/250 VAC will prevent reset failure. Also, as mentioned above, the l...
- faq02235
...heat radiated by Solid-state Relays can be found using the following equation. Heating value P (W) = Output-ON voltage drop (V) x Carry current (A) For example, if a load current of 8 A flows...
- FAQ02237 for Solid-state Relays | OMRON Industrial...
...with the power supply to keep the Solid-state Relay ON. Bleeder Resistance 100 VAC 5 to 10 kΩ 3 W 200 VAC 5 to 10 kΩ 15 W MY Best-selling, general-purpose relays that can be selected...
- faq03116
...g method Surface mounting 8-pin socket 8-pin socket Flush mounting panel cutout 43.5 x 50.5 mm (W x H) (H3A-Y) 45 x 55 mm (W x H) (H3A + Y92F-40) 45 x 45 mm (W x H) (H3CR-A8...
- faq03132
... type Flush mounting: 1 type Mounting method Surface mounting Three M4 screw holes 74 x 102 mm (W x H) Triangle (H2E, -P, 2) 80 x 120 mm (W x H) Triangle (H2E-M, MP) Two M3 screw hol...
- faq03173
...Flush mounting) H3AM: 1 type (Flush mounting only) Flush mounting only panel cutout 52 x 66 mm (W x H) (TDS-Y) 53 x 65 mm (W x H) (TDS + Y92F-50) 81 dai. (TDS-LS) 45 x 45 mm (...
- faq01858
...'s internal loss becomes heat energy (internal loss = heat produced). Equations: Internal loss (W) = Effective input power - Output power = Output power/Efficiency - Output power Note:Reducin...
- faq01913
...normal level automatically (automatic recovery) when the overcurrent status is cleared. S82K: 3 W, 7.5 W, 15 W S8VS: 15 W Inverted L voltage drop When a voltage dro...
- faq01928
...use forced cooling.) S82J Note:Whenever possible, install Power Supply on metal plates. For 300-W and 600-W Power Supplies, space must be provided in front of and behind Power Suppli...
- faq01942
...s Supporting Series Connection of Outputs Model Power ratings Rated output voltage S82K 90, 100 W 24 VDC S82J 100 W 5, 12, 15, 24 VDC 50, 150, 300, 600 W 24 VDC S8TS 25, 30,...
- faq01967
...parated from the internal circuit by capacitors. Example: Block Diagram of S82J-050[][][][] (50 W) Switch Mode Power Supply S8VS Multi-Function Indication Monitor for Production Site Visualiz...
- faq02011
...nnection method S82K-10024 S8T-DCBU-02 Only connect the +V and -V outputs in parallel S82K (100 W (- P type only) S82J (300, 600 W) Connect the +V and -V outputs in parallel and set ...
- faq03417
...available. Model File No. Remarks S82J (10 (excluding 5V), 25 (excluding 5V), 50 (excluding 24V)W) E104818 --- S82K (3, 7.5, 15, 30, 50, 90W) --- S82K (100W) External fuse required S8TS (30, ...
- faq03632
...l configuration? Answer It depends on the capacity. Parallel operation is not possible for 15-W, 30-W, 50-W, 100-W, and 150-W Power Supplies. Parallel op...
- FAQ01184 for Photomicro Sensors | OMRON Industrial...
... the following diagrams. EE-SX77 EE-SX47[]/SX67[] EE-SPX74[] EE-SPX740/742/743 EE-SPX741 EE-SPX-W EE-SPX302-W2A EE-SPX304-W2A EE-SPX306-W2A EE-SPX305-W2A EE-SPX303 EE-SPX301 E2E Standard Sens...
- faq02799
...l Values) Bleeder Resistance for MY4 AC100/110V Float capacitance (μF) Resistance (kΩ) Wattage (W) 0.05 max. Not required. - 0.05 to 0.15 7 2 0.15 to 0.17 6 2.5 0.17 to 0.19 5 3 0.19 to 0.23 ...
Top of page
OMRON Corporation