...ng the screw-less clamp terminal ・Directly insert the ferrule in the hole of the terminal to be wired. Removing wires from the screw-less clamp terminal ・Insert the recommended flat-blade s...

https://www.fa.omron.com.cn/data_pdf/mnu/n159-e1-02_k8ac-h.pdf

...nications errors occur. Possible cause Location to check Reference pages Communications are not wired properly. Correct the wiring. 1-4 The communications cable is disconnecting. Connect the ...

https://www.fa.omron.com.cn/data_pdf/mnu/n165-e1-01_km50.pdf

...re is already installed, go to step 15. Network card configuration example If there is only one wired LAN port of the computer and the Motor condition monitoring Tool com- municates with the ...

https://www.fa.omron.com.cn/data_pdf/mnu/n219-e1-16_k6cm.pdf

...l (N227) (I) 19 and 20 CH2 CT input The CT connected to the heater current measurement point is wired to this terminal, and the K7TM measures the heater current. This is the second input of t...

https://www.fa.omron.com.cn/data_pdf/mnu/n227-e1-07_k7tm.pdf

...re anything to the release holes. (12)Confirm that the input and output terminals are correctly wired before power is supplied. (13)The terminal block may be damaged if you insert a flat-blad...

https://www.fa.omron.com.cn/data_pdf/mnu/n233-e1-04_k7dd.pdf

...cable. •It is recommended that the Cam Positioner cables and other control and power cables are wired as shown below. •Parallel cable racks must be a minimum of 300 mm apart. •If multiple ter...

https://www.fa.omron.com.cn/data_pdf/mnu/o008-e1-04_3f88l-160_162.pdf

...seconds before servo-ing the Motor again •Make sure Motor wiring is using proper wire gauge and wired correctly •Check that the Motor chassis is grounded and does not have potential voltage •...

https://www.fa.omron.com.cn/data_pdf/mnu/o050-e1-05_ck3a-g___l.pdf

...ct input wiring and zone configuration selection. Check zone set select inputs or standby input wired at more than system power (24 VDC). Check that the window is properly mounted and clean t...

https://www.fa.omron.com.cn/data_pdf/mnu/os32c_inst-99863-0020n.pdf

....1. Calculate the alarm currents according to what type of heater is used and how the heater is wired. For details, refer to 7-7 CT Installation and Alarm Current Calculation described in the...

https://www.fa.omron.com.cn/data_pdf/mnu/p105-e1-01_nx-hb____.pdf

...e I/O Cable Turn ON the 24 VDC power supply. *In this document, only the power supply lines are wired. Note that so as not to short-circuit the other lines. *For details on I/O Cable, refer t...

https://www.fa.omron.com.cn/data_pdf/mnu/p550-e1-01_fq2.pdf

...ad and heed the information provided in all safety precautions of manuals for each device to be wired. If you change the values of variables on a Watch Tab Page in the online state, the devic...

https://www.fa.omron.com.cn/data_pdf/mnu/p640-e1-01_3g3mx2-v1.pdf

... follow the information provided in all safety precautions in the manuals for each device to be wired. If the PLC memory is changed by malfunction during monitoring power flow and present val...

https://www.fa.omron.com.cn/data_pdf/mnu/p656-e1-01_nx.pdf

...up Initialization 0: Not initialize CPU Bus Unit PLC Setup 1: Initialize CPU Bus Unit PLC Setup Wired Network 62 Node Enable Bit 0: 32 nodes max. 1: 62 nodes max. Data Link status Storage for...

https://www.fa.omron.com.cn/data_pdf/mnu/r123-e1-01_fb_library.pdf

...on can be verified before actual devices such as the PLC and PT (touch panel) are installed and wired, so software quality can be improved in the design stage.  Time can be saved by eliminat...

https://www.fa.omron.com.cn/data_pdf/mnu/r145-e1-04_cx-one.pdf

...nsor1 Sensor2 Black Black Brown Brown Blue Blue ON OFF ON OFF ON OFF Note: When two sensors are wired OR and then receive input (IN1 orIN2),OR operation is possible. Sensor1 Sensor2 (IN...

https://www.fa.omron.com.cn/data_pdf/mnu/s3d2_inst-1610610-5d1.pdf

...NORM) Output(AND) NORM NORM IN1 IN2 S3D2-AK/-AKD 7 8 9 10 11 12 4 5 6 1 2 3 ON OFF ON OFF (IN1F wired OR) ON OFF NORM INV IN1 IN2 S3D2-AK/-AKD 7 8 9 10 11 12 4 5 6 1 2 3 ON OFF ON OFF IN1 IN2...

https://www.fa.omron.com.cn/data_pdf/mnu/s3d2_inst-6918249-0f.pdf

...onnected completely. •Minor fire may possibly occur. Ensure that input and output terminals are wired correctly. •To prevent wiring materials from smoking or ignition, confirm wire ratings an...

https://www.fa.omron.com.cn/data_pdf/mnu/s8as2_inst-5833886-3b.pdf

...unction may occur. 2. Minor fire may possibly occur. Ensure that input and output terminals are wired correctly. 3. Heat generated by wiring materials may cause the temperature of internal pa...

https://www.fa.omron.com.cn/data_pdf/mnu/s8as_inst-1118602-0c.pdf

...unction may occur. 2. Minor fire may possibly occur. Ensure that input and output terminals are wired correctly. 3. Heat generated by wiring materials may cause the temperature of internal pa...

https://www.fa.omron.com.cn/data_pdf/mnu/s8as_inst-1125366-5c.pdf

...unction may occur. 2. Minor fire may possibly occur. Ensure that input and output terminals are wired correctly. 3. It is conceivable that internal parts may be deteriorated or damaged. Do no...

https://www.fa.omron.com.cn/data_pdf/mnu/s8as_inst-9975609-2a.pdf