...e reset Outputs M codes, and interlocks with sequence control program using reset. Spindle axis CW/CCW/Stop Outputs/stops velocity commands in velocity loop control mode. Orientation Stops sp...

https://www.omron-ap.com.my/products/family/3679/specification.html

...ve logic (high = 0, low = 1) Accuracy ±1° max. Direction of rotation Output code incremented by CW (as viewed from the end of the shaft) Rise and fall times of output 1 μs max. (Control outpu...

https://www.omron-ap.com.my/products/family/494/specification.html

...0, low = 1) Positive logic (high = 1, low = 0) Direction of rotation Output code incremented by CW (as viewed from the end of the shaft) Rise and fall times of output 1 μs max. (E6F-AB3C, A[]...

https://www.omron-ap.com.my/products/family/496/specification.html

... low = 1) Positive logic (high = 1, low = 0) Direction of rotation *4 Output code increases for CW (as viewed from end of shaft). Switched using rotation direction input. Strobe signal None S...

https://www.omron-ap.com.ph/products/family/1347/specification.html

...puter hard disk or floppy disk. External I/O Inputs Prepare the following inputs for each axis: CW and CCW limit input signals, origin proximity input signal, origin input signal, emergency s...

https://www.omron-ap.com.ph/products/family/1409/specification.html

... outputs) Line-driver inputs: Two axes for phases A, B, and Z Line-driver outputs: Two axes for CW and CCW Number of connectable Expansion (I/O) Units CP Expansion I/O Units: 7 max.; CJ-serie...

https://www.omron-ap.com.ph/products/family/1778/specification.html

...r S-curve acceleration and deceleration (Duty ratio: 50% fixed) 2 outputs, 1 Hz to 100 kHz (CCW/CW or pulse plus direction) PWM outputs Duty ratio: 0.0% to 100.0% (specified in increments of ...

https://www.omron-ap.com.ph/products/family/1916/specification.html

...s 12 max. (6 per Pulse I/O Module) Pulse Outputs 4 max. (2 per Pulse I/O Module) Output method: CW/CCW or pulse + direction (The method is determined by the I/O wiring and the instructions us...

https://www.omron-ap.com.ph/products/family/2712/specification.html

...e reset Outputs M codes, and interlocks with sequence control program using reset. Spindle axis CW/CCW/Stop Outputs/stops velocity commands in velocity loop control mode. Orientation Stops sp...

https://www.omron-ap.com.ph/products/family/3679/specification.html

...ve logic (high = 0, low = 1) Accuracy ±1° max. Direction of rotation Output code incremented by CW (as viewed from the end of the shaft) Rise and fall times of output 1 μs max. (Control outpu...

https://www.omron-ap.com.ph/products/family/494/specification.html

...0, low = 1) Positive logic (high = 1, low = 0) Direction of rotation Output code incremented by CW (as viewed from the end of the shaft) Rise and fall times of output 1 μs max. (E6F-AB3C, A[]...

https://www.omron-ap.com.ph/products/family/496/specification.html

... low = 1) Positive logic (high = 1, low = 0) Direction of rotation *4 Output code increases for CW (as viewed from end of shaft). Switched using rotation direction input. Strobe signal None S...

https://www.omron-ap.com/products/family/1347/specification.html

...puter hard disk or floppy disk. External I/O Inputs Prepare the following inputs for each axis: CW and CCW limit input signals, origin proximity input signal, origin input signal, emergency s...

https://www.omron-ap.com/products/family/1409/specification.html

... outputs) Line-driver inputs: Two axes for phases A, B, and Z Line-driver outputs: Two axes for CW and CCW Number of connectable Expansion (I/O) Units CP Expansion I/O Units: 7 max.; CJ-serie...

https://www.omron-ap.com/products/family/1778/specification.html

...r S-curve acceleration and deceleration (Duty ratio: 50% fixed) 2 outputs, 1 Hz to 100 kHz (CCW/CW or pulse plus direction) PWM outputs Duty ratio: 0.0% to 100.0% (specified in increments of ...

https://www.omron-ap.com/products/family/1916/specification.html

...e reset Outputs M codes, and interlocks with sequence control program using reset. Spindle axis CW/CCW/Stop Outputs/stops velocity commands in velocity loop control mode. Orientation Stops sp...

https://www.omron-ap.com/products/family/3679/specification.html

...ve logic (high = 0, low = 1) Accuracy ±1° max. Direction of rotation Output code incremented by CW (as viewed from the end of the shaft) Rise and fall times of output 1 μs max. (Control outpu...

https://www.omron-ap.com/products/family/494/specification.html

...0, low = 1) Positive logic (high = 1, low = 0) Direction of rotation Output code incremented by CW (as viewed from the end of the shaft) Rise and fall times of output 1 μs max. (E6F-AB3C, A[]...

https://www.omron-ap.com/products/family/496/specification.html

... low = 1) Positive logic (high = 1, low = 0) Direction of rotation *4 Output code increases for CW (as viewed from end of shaft). Switched using rotation direction input. Strobe signal None S...

https://www.omron.co.id/products/family/1347/specification.html

...puter hard disk or floppy disk. External I/O Inputs Prepare the following inputs for each axis: CW and CCW limit input signals, origin proximity input signal, origin input signal, emergency s...

https://www.omron.co.id/products/family/1409/specification.html