...M Area.) Note 1. Errors and fluctuations will increase when the input signal pulse rate is low, so specify a longer time unit. Note 2. The instantaneous value is only refreshed at intervals o...

https://www.omron-ap.co.nz/products/family/1671/specification.html

...ies, Ltd. - * There is a risk of quality problems when using cables assembled by typical users, so we recommend purchasing   cables with preattached connectors or having a qualified technicia...

https://www.omron-ap.co.nz/products/family/1681/lineup.html

... socket.              When using the short bars on the upper section of the socket, insert them so that their heads are pointed upwards              (see the figure below).              Other...

https://www.omron-ap.co.nz/products/family/1731/lineup.html

... time. *2. The Data Collection Patterns use the data collected by the Basic Collection Pattern, so the data will be collected at the        Basic Collection Pattern’s interval even if the Dat...

https://www.omron-ap.co.nz/products/family/1732/specification.html

... hot start is performed when the power supply has been OFF for only a short               time, so in those cases the inrush current values may be higher (as much as two times higher) than th...

https://www.omron-ap.co.nz/products/family/1778/specification.html

...eries Controllers only. *2. Drop-line connections are not supported with a baud rate of 4 Mbps, so Slaves with prewired cables (Bit Slaves)        cannot be used. *3. Round cable, Flat Cable,...

https://www.omron-ap.co.nz/products/family/1779/specification.html

...ns manual startup mode I/O Communications Manual Startup Mode can be set from the CX-Integrater so that remote I/O communications are not started when the power is turned ON.Remote I/O commun...

https://www.omron-ap.co.nz/products/family/1781/specification.html

...model most suited to the application. *3. Set the distance between the Sensor and the Reflector so that it is at least the value in parentheses. Accessories Sensor I/O Connectors (Sockets on ...

https://www.omron-ap.co.nz/products/family/1853/lineup.html

...d if a hot start is performed when the power supply has been OFF for only a short time,         so in those cases the inrush current values may be higher (as much as two times higher) than th...

https://www.omron-ap.co.nz/products/family/1916/specification.html

... ZX-GTC41 Accessories (Order Separately) These are not included with the sensor and controller, so order these accessories separately if necessary. Set: Interface Unit (RS-232C/Binary output)...

https://www.omron-ap.co.nz/products/family/1918/lineup.html

...s a shaft with key and tap. (The key is temporarily assembled to the shaft.) Note: 5. Take care so that the surface temperature of the Decelerator does not exceed 90°C. Decelerator for Flat S...

https://www.omron-ap.co.nz/products/family/1956/specification.html

...registers for storing PLC memory addresses for indirect addressing. (Index Registers can be set so that they are unique in each task or so that they are shared by all tasks.) Cyclic ...

https://www.omron-ap.co.nz/products/family/1993/specification.html

...registers for storing PLC memory addresses for indirect addressing. (Index Registers can be set so that they are unique in each task or so that they are shared by all tasks.) Cyclic ...

https://www.omron-ap.co.nz/products/family/2045/specification.html

...llows for repetition of a given operation, start/end of operation data via external inputs, and so on. Accordingly, the PCU can perform various operation sequences without affecting the ladde...

https://www.omron-ap.co.nz/products/family/2051/specification.html

... 1 to 5 mm.            2. To allow easier operation, it is recommended that Adapters be mounted so that the gap between sides with                  hooks is at least 15 mm (i.e., with the pan...

https://www.omron-ap.co.nz/products/family/207/dimension.html

...e is enabled.       • The dynamic brake is designed only for emergency stops. Design the system so that the Servomotor remains         stopped for at least 10 minutes after applying the dynam...

https://www.omron-ap.co.nz/products/family/2611/specification.html

...e is enabled.       • The dynamic brake is designed only for emergency stops. Design the system so that the Servomotor remains         stopped for at least 10 minutes after applying the dynam...

https://www.omron-ap.co.nz/products/family/2627/specification.html

...e is enabled.       • The dynamic brake is designed only for emergency stops. Design the system so that the Servomotor remains         stopped for at least 10 minutes after applying the dynam...

https://www.omron-ap.co.nz/products/family/2644/specification.html

...grated lens Top-view 4° E32-D16 2M 800 140 40 to 400 *1. The fiber length is 10 m on each side, so the sensing distance is given as 20,000 mm. *2. The fiber length is 2 m on each side, ...

https://www.omron-ap.co.nz/products/family/2647/specification.html

...registers for storing PLC memory addresses for indirect addressing. (Index Registers can be set so that they are unique in each task or so that they are shared by all tasks.) Cyclic ...

https://www.omron-ap.co.nz/products/family/2712/specification.html