Industrial Automation

Global

Global Navigation

Primary Contents

Site Search Results

Site Search Product Search IA Global Search
Results 5011 - 5020 of 6521
K7GE-MG Insulation Resistance Monitoring Device/Fe...
...not require manual tasks. Reduced risk of equipment failure due to measurement with fixed DC 50 V Conventional measurement with a typical Megohmmeter requires selecting a voltage range in acc...

https://www.ia.omron.com/products/family/3811/feature.html

Further Information of Timers | OMRON Industrial A...
... VDC 600 mA 1 ms H5AN series 100 to 240 VAC 264 VAC 23 A 1 ms 100 VDC 110 VDC 8 A 2 ms 12 to 24 V DC 26.4 VDC 15 A 6.5 ms H5CN series 100 to 240 VAC 264 VAC 800 mA 1 ms 12 to 48 VDC 52.8 VDC ...

https://www.ia.omron.com/support/guide/19/further_information.html

Further Information of Power Supplies | OMRON Indu...
...ends on the specifications of the DC-DC converter, but some will start as low as approx. 3 to 4 V. If more than one load with these characteristics is connected, the startup current will atte...

https://www.ia.omron.com/support/guide/22/further_information.html

Further Information of General Purpose Relays | OM...
...which the status of the contacts remains unaffected is called the softening voltage. It is 0.09 V for silver, 0.08 V for gold, 0.25 V for platinum, and 0.6 V for tu...

https://www.ia.omron.com/support/guide/36/further_information.html

explanation_of_terms.html
...rated output current. 3.Do not apply unnecessarily strong force to the Output Voltage Adjuster (V.ADJ). Doing so may damage the V.ADJ. Ripple and Noise Since Switch-mode Power Suppli...

https://www.ia.omron.com/support/guide/22/explanation_of_terms.html

troubleshooting.html
...Output Voltage Adjuster Do not apply unnecessarily strong force on the Output Voltage Adjuster (V.ADJ). Doing so may damage the V.ADJ. Make sure that the end of the screwdriver used ...

https://www.ia.omron.com/support/guide/22/troubleshooting.html

troubleshooting.html
...1 and E 3 ) is given by the following equation. R: Resistance of liquid between electrodes (kΩ) V: Voltmeter indicated voltage (V) I: Ammeter indicated current (mA) Select the 61F mo...

https://www.ia.omron.com/support/guide/33/troubleshooting.html

Further Information of Rotary Encoders | OMRON Ind...
...ollector Output (5/12/24 VDC) Note: Connections are as follows if the Encoder power supply is 5 V or 24 V. Phase A + 5-V power supply → A19, 24 V → B20 Phase B + 5-...

https://www.ia.omron.com/support/guide/34/further_information.html

explanation_of_terms.html
...e waveform according to JIS C5442, i.e., 1.2 × 50 μs. FCC Part 68 specifies 10 × 160 μs ± 1,500 V. Vibration categories: Destruction, which quantifies the characteristic changes of, or damage...

https://www.ia.omron.com/support/guide/36/explanation_of_terms.html

explanation_of_terms.html
...t signal. When using them, pull up to the positive power supply voltage level or pull down to 0 V. The Complementary Output allows flow-in or flow-out of the output current and thus the risin...

https://www.ia.omron.com/support/guide/34/explanation_of_terms.html

Results 5011 - 5020 of 6521

Related Contents

Site Information

© Copyright OMRON Corporation 2007 - . All Rights Reserved.