Industrial Automation

Global

Global Navigation

Primary Contents

Site Search Results

Site Search Product Search IA Global Search
Results 5031 - 5040 of 6521
Correct use of Rotary Encoders | OMRON Industrial ...
...utput, a power supply of 5 VDC is needed for the Encoder. The voltage will drop approximately 1 V per 100 m of cable. ...

https://www.ia.omron.com/product/cautions/52/precautions_for_correct_use.html

Further Information of Frequency Inverters Technic...
...lculate a regenerative energy and make your selection. Calculation of Required Braking Resistor V: 200V class inverter 385 [V] 　 400V class inverter 760 [V] T: Maximum Brak...

https://www.ia.omron.com/support/guide/25/further_information.html

Safety Precautions of Counters Cautions for Counte...
...form to the rated conditions. Note:The residual voltage is the voltage between the output and 0-V lines when the transistor is ON (i.e., the total voltage between both edges of the transistor...

https://www.ia.omron.com/product/cautions/11/safety_precautions.html

Safety Precautions of Solid-state Relays Cautions ...
...he surge absorbing element. Voltage Varistor voltage Surge resistance 100 to 120 VAC 240 to 270 V 1,000 A min. 200 to 240 VAC 440 to 470 V 380 to 480 VAC 820 to 1,000 V Outp...

https://www.ia.omron.com/product/cautions/18/safety_precautions.html

Safety Precautions of Timers Cautions for Timers |...
...wing as guides for C and R values: C: 0.5 to 1 μF for a 1-A contact current R: 0.5 to 1 Ω for 1-V contact voltage However, these values may depend on numerous factors, including the type of l...

https://www.ia.omron.com/product/cautions/19/safety_precautions.html

Safety Precautions of Power Supplies Cautions for ...
...ng output (i.e., the primary side and secondary side are separated), so the output line (i.e., +V or -V) can be connected externally directly to a ground. Through the ground, however...

https://www.ia.omron.com/product/cautions/22/safety_precautions.html

Safety Precautions of Photomicro Sensors Cautions ...
...ce of 0.1 to 1 μF) or a Zener diode (Z D in the diagram below, with a rated voltage of 30 to 35 V). Use the Sensor only after confirming that the surge has been removed. • When driving a smal...

https://www.ia.omron.com/product/cautions/24/safety_precautions.html

Safety Precautions of Basic Switches Cautions for ...
... R impedance. C: 0.5 to 1 μF per switching current (1 A) R: 0.5 to 1 Ω per switching voltage (1 V) The values may change according to the characteristics of the load. The capacitor suppresses...

https://www.ia.omron.com/product/cautions/29/safety_precautions.html

Safety Precautions of Limit Switches Cautions for ...
...han the CR impedance. C: 1 to 0.5 μF × switching current (A) R: 0.5 to 1 Ω × switching voltage (V) The values may change according to the characteristics of the load. The capacitor suppresses...

https://www.ia.omron.com/product/cautions/30/safety_precautions.html

Safety Precautions of Rotary Encoders Cautions for...
...utput, a power supply of 5 VDC is needed for the Encoder. The voltage will drop approximately 1 V per 100 m of cable. Using a Line Receiver IC Recommended IC: ICs from Texas Instruments Incor...

https://www.ia.omron.com/product/cautions/34/safety_precautions.html

Results 5031 - 5040 of 6521

Related Contents

Site Information

© Copyright OMRON Corporation 2007 - . All Rights Reserved.