GlobalSite Search Results
| Site Search | Product Search | IA Global Search |
previous
Sensors Switches Safety Components Relays Control ...- ...inals 1 and 3, respectively. The G3PW may be damaged if a command voltage that is higher than 5 V is applied. If it is necessary to apply more than 5 V, split the voltage as shown be...
https://www.ia.omron.com/data_pdf/guide/54/power_controllers_tg_e_5_2.pdf
- Sensors Switches Safety Components Relays Control ...
- ...BCD Linear Communications DeviceNet Voltages/Currents Pulses Sensors Temperature Sensors 1 to 5 V 4 to 20 mA Inputs Outputs A Wide Range of Voltages/Currents A V A V ～――～ ...
https://www.ia.omron.com/data_pdf/guide/62/digital_panel_tg_e_3_3.pdf
- Sensors Switches Safety Components Relays Control ...
- ...n the input is at the minimum value or there is no input). For example, if the output is 1 to 5 V, 1 V is the output bias. If the output is 0 to 5 V, 0 V is the out...
https://www.ia.omron.com/data_pdf/guide/63/signals_tg_e_1_3.pdf
- Sensors Switches Safety Components Relays Control ...
- ...). With I1 and I2, |I1| = |I2| just as in normal operation with a phase difference of 120°. The V-phase power supply line current then is again just as in normal operation while the U- and W-...
https://www.ia.omron.com/data_pdf/guide/65/epsc_ps_tg_e_2_3_measuring_monitoringry_tg_e_1_2.pdf
- Sensors Switches Safety Components Relays Control ...
- ...ction procedure] [Application] [Selection] Check the load capacity (kW) Check the load voltage (V) Check the operating voltage (V) Thermal overload relay used? Check the thermal over...
https://www.ia.omron.com/data_pdf/guide/753/lowvoltageswitchinggears_tg_e_2_1.pdf
- Sensors Switches Safety Components Relays Control ...
- ...neral-purpose inverter cannot be used for equipment other than motors. Principles Control Modes V/f Control V/f control is a method of controlling a motor by supplying a specific cur...
https://www.ia.omron.com/data_pdf/guide/9/inverter_tg_e_2_1.pdf
explanation_of_terms.html- ... is called cold junction compensation. In the above diagram, the thermo-electromotive force (1) V T that is measured at the input terminal of the Temperature Controller is equal to V...
https://www.ia.omron.com/support/guide/53/explanation_of_terms.html
- OMRON Corporation Industrial Automation Company No...
- ...tion ] Before After Intelligent CCD Cameras, Autofocus CCD Cameras Effective pixels: 640(H)×480(V) Intelligent CCD Cameras, Autofocus CCD Cameras Effective pixels: 659(H)×494(V) Befo...
- OMRON Corporation Industrial Automation Company No...
- ...g a test object ofϕ80 mm and actuating point C3 under a test temperature of 20°C and test speed v = 10 mm/s. Refer to“Characteristics”for details. *2. There is an inactive region (including a...
- OMRON Corporation Industrial Automation Company No...
- ...ives 1S-series User’s Manual (I586-E1-02) P2-28, 2-29 Before After 3,000-r/min Servomotors (100 V and 200 V) 100 W (without Brake) R88M-1M10030S(-O/-S2/-OS2) R88M-1M10030T(-O/-S2/-OS...
Top of page
© Copyright OMRON Corporation 2007 -
. All Rights Reserved.
OMRON Corporation