Industrial Automation

Global

Global Navigation

Primary Contents

Site Search Results

Site Search Product Search IA Global Search
Results 941 - 950 of 1183
PDFCSM_G7J_DS_E_6_6 1 Power Relay G7J
...Refer to the following diagram when connecting a wire with a screw terminal to the G7J. Install so that the washer, crimp terminal, and terminal are parallel and in close contact, and tighten...

https://www.ia.omron.com/data_pdf/cat/g7j_ds_e_6_6_csm49.pdf

PDFCSM_G7S-_-E_DS_E_7_3 1 Relays with Forcibly Guided...
...ts of 6 A or more when using this product in combination with the P7S-14F/14P/14A Socket. Doing so may result in fire. Use this product in combination with the P7S-14F-END/14P-E. Precautions ...

https://www.ia.omron.com/data_pdf/cat/g7s-_-e_ds_e_7_3_csm1272.pdf

PDF1 Relays with Forcibly Guided Contacts G7SA
.... •Do not bend a wire past its natural bending radius or pull on it with excessive force. Doing so may cause the wire disconnection. •Do not insert more than one wire into each terminal inser...

https://www.ia.omron.com/data_pdf/cat/g7sa_j120-e1_12_13_csm1269.pdf

PDFCSM_G7TC_DS_E_9_1 1 I/O Relay Terminal G7TC
...t Relays (DC coil type) and I/O SSRs (DC input type) can be mounted onto an Output Block. Doing so enables using controller programming to simultaneously switch on or off two outputs (DPST- N...

https://www.ia.omron.com/data_pdf/cat/g7tc_ds_e_9_1_csm1046354.pdf

PDF1 Power Relays G7Z Compact Electromagnetic Contact...
...table slack on leads when wiring, and do not subject the terminals to excessive force. •Install so that the washer, crimp terminal, and terminal are parallel and in close contact, and tighten...

https://www.ia.omron.com/data_pdf/cat/g7z_j160-e1_10_1_csm1001495.pdf

PDFCSM_G9B_DS_E_4_1 1 Stepping Relay Unit
...ts default status (i.e., contact 01 of the G9B will be turned ON) and turn its alarm contact ON so that the ALARM indicator of the G9B will become lit. When the G9B is turned OFF, the alarm c...

https://www.ia.omron.com/data_pdf/cat/g9b_ds_e_4_1_csm53.pdf

PDF1 Safety Relay Unit with negative common (NPN)
...for power supply. Connect the power source to the A1 and A2 terminals. DC inputs have polarity, so A1 should be connected to the positive side and A2 to the negative side. Safety input 1 T11,...

https://www.ia.omron.com/data_pdf/cat/g9sa-p_f106-e1_6_2_csm1070131.pdf

PDFCSM_G9SA_DS_E_11_15 1 Safety Relay Unit G9SA
...for power supply. Connect the power source to the A1 and A2 terminals. DC inputs have polarity, so A1 should be connected to the positive side and A2 to the negative side. Safety input 1 T11,...

https://www.ia.omron.com/data_pdf/cat/g9sa_ds_e_11_15_csm1281.pdf

PDFCSM_G9SB_DS_E_6_7 1 Safety Relay Unit G9SB
...for power supply. Connect the power source to the A1 and A2 terminals. DC inputs have polarity, so A1 should be connected to the positive side and A2 to the negative side. Safety input 1 *1T1...

https://www.ia.omron.com/data_pdf/cat/g9sb_ds_e_6_7_csm1282.pdf

PDFSafety Relay Unit Authorized Distributor:
...h KM1, KM2: Magnetic contactor M: Motor Note: The lock release enable signal must be configured so that it should turn ON after dangerous movement is stopped and safety is ensured for the doo...

https://www.ia.omron.com/data_pdf/cat/g9se_j198-e1_4_7_csm1040781.pdf

Results 941 - 950 of 1183

Related Contents

Site Information

© Copyright OMRON Corporation 2007 - . All Rights Reserved.