Industrial Automation

Global

Global Navigation

Primary Contents

Site Search Results

Site Search Product Search IA Global Search
Results 951 - 960 of 1186
PDFCSM_G9SA_DS_E_11_15 1 Safety Relay Unit G9SA
...for power supply. Connect the power source to the A1 and A2 terminals. DC inputs have polarity, so A1 should be connected to the positive side and A2 to the negative side. Safety input 1 T11,...

https://www.ia.omron.com/data_pdf/cat/g9sa_ds_e_11_15_csm1281.pdf

PDFCSM_G9SB_DS_E_6_7 1 Safety Relay Unit G9SB
...for power supply. Connect the power source to the A1 and A2 terminals. DC inputs have polarity, so A1 should be connected to the positive side and A2 to the negative side. Safety input 1 *1T1...

https://www.ia.omron.com/data_pdf/cat/g9sb_ds_e_6_7_csm1282.pdf

PDFSafety Relay Unit Authorized Distributor:
...h KM1, KM2: Magnetic contactor M: Motor Note: The lock release enable signal must be configured so that it should turn ON after dangerous movement is stopped and safety is ensured for the doo...

https://www.ia.omron.com/data_pdf/cat/g9se_j198-e1_4_7_csm1040781.pdf

PDF»Flexible range suits any system
...ures are added to your set-up. Three different models are available, with a range of I/O lines, so you can choose the most suitable for your system. Each one is compatible with the Omron conf...

https://www.ia.omron.com/data_pdf/cat/g9sp_f090-e1_12_9_csm2603.pdf

PDFG9SX-AD@/BC/EX G9SX-GS G9SX-SM G9SX-NS
...ious injury may possibly occur due to loss of required safety functions. Wire the G9SX properly so that the safety outputs do not short-circuit with the Unit power supply or load power supply...

https://www.ia.omron.com/data_pdf/cat/g9sx_series_f120-e1_1_6_csm1119023.pdf

PDFModel Selection Guide for Timers
...e switched. Either AC or DC load voltages can be used. Transistor output There are no contacts, so high-speed, high-frequency switching is possible. Only DC can be switched and the capacity i...

https://www.ia.omron.com/data_pdf/cat/h3_h5_timer_selection_guide_l130-e1_2_1_csm1129246.pdf

PDF1 Solid-state Timer H3CR Please read and understan...
... is connected to two or more Timers, the input terminals of those Timers must be wired properly so that they will not differ in phase, otherwise the terminals will be short-circuited to one a...

https://www.ia.omron.com/data_pdf/cat/h3cr_l084-e1_3_6_csm1013792.pdf

PDF1 Solid-state Timers H3DK DIN Track-mounted, 22.5-...
...auge: AWG18 to AWG22 (for stranded wire) •Install and clearly label a switch or circuit breaker so that the operator can quickly turn OFF the power supply. •If the Timer is left in the timed ...

https://www.ia.omron.com/data_pdf/cat/h3dk_l118-e1_7_7_csm2645.pdf

PDFCSM_H3DS_DS_E_5_4 1 Solid-state Timer H3DS
... is connected to two or more Timers, the input terminals of those Timers must be wired properly so that they will not be different in phase or the terminals will be short-circuited to one ano...

https://www.ia.omron.com/data_pdf/cat/h3ds_ds_e_5_4_csm88.pdf

PDF1 Solid-state Timers H3DT DIN 17.5-mm-wide Slim Ti...
.... •Do not bend a wire past its natural bending radius or pull on it with excessive force. Doing so may cause the wire disconnection. •Do not insert more than one wire into each terminal inser...

https://www.ia.omron.com/data_pdf/cat/h3dt_m090-e1_4_8_csm1050135.pdf

Results 951 - 960 of 1186

Related Contents

Site Information

© Copyright OMRON Corporation 2007 - . All Rights Reserved.