GlobalIA Global Search Results
| Site Search | Product Search | IA Global Search |
previous
FAQ00903 for Counters | OMRON Industrial Automatio......ts Question Which Relays are compatible with the H7EC-N and H7ET-N Counters that use no-voltage input? Answer Recommended model: OMRON Solid-state Relay the G3TA-IA/ID K3HB-X A Process Indi...
- FAQ00904 for Counters | OMRON Industrial Automatio...
...7 ms (minimum ON signal width and OFF signal width) Description ON/OFF Ratio Ratio of the count input signal's ON time to OFF time. (The Counter's maximum counting speed is specified at an ON...
- FAQ00914 for Counters | OMRON Industrial Automatio...
... output will turn ON until the target is reached. 2. Reset Method Turn ON the batch count reset input to reset the batch output and batch count display. Applicable Models: H7BR-B, H7CX-A4W[],...
- FAQ00918 for Counters | OMRON Industrial Automatio...
...Current Signals E5CN-H A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. H5CZ Easy to Use and Easy...
- FAQ00922 for Counters | OMRON Industrial Automatio...
...Current Signals E5CN-H A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. H5CZ Easy to Use and Easy...
- FAQ01497 for Counters | OMRON Industrial Automatio...
...Current Signals E5CN-H A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. H5CZ Easy to Use and Easy...
- FAQ01506 for Counters | OMRON Industrial Automatio...
...Current Signals E5CN-H A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. H5CZ Easy to Use and Easy...
- FAQ01508 for Counters | OMRON Industrial Automatio...
...Current Signals E5CN-H A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. H5CZ Easy to Use and Easy...
- faq03177
...perating mode Incremental type Mounting method Flush mounting Direct mounting on PC board Count input No-voltage input DC voltage input Multi-voltage No-voltage ...
- FAQ03185 for Counters | OMRON Industrial Automatio...
...Current Signals E5CN-H A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. H5CZ Easy to Use and Easy...
- faq03357
... FAQ03357 Related Contents Primary Contents Question When inputs CP1 and CP2 are simultaneously input to H7CX Multifunction Preset Counters when used as a dual counter, are both of them count...
- faq03596
...that 60 (seconds) ÷ 30 (revolutions) = 2 (seconds per revolution) Therefore a pulse is normally input every 2 seconds. When the rate of rotation falls to 10 revolutions per minute (10 rpm), 6...
- faq03598
...Current Signals E5CN-H A New High-performance Controller: High Resolution, High Speed, and High Input Accuracy. Logic Operations and Preventive Maintenance Function. H5CZ Easy to Use and Easy...
- FAQ00191 for Servomotors / Servo Drivers | OMRON I...
...in the main circuit. An error is detected when a low voltage was detected in the main circuit's input section and lasted longer than 50 ms. The likely causes of the error are that the main vo...
- FAQ01684 for Servomotors / Servo Drivers | OMRON I...
...ve the rubber cap and check that the set bolt is loose. 2. Insert the Servomotor shaft into the input shaft. 3. Tighten the Servomotor installation bolt according to the tightening torque spe...
- FAQ02279 for Safety Relays | OMRON Industrial Auto...
...ys Lead Contents FAQ No. FAQ02279 Related Contents Primary Contents Question What is an inverse input? Answer An inverse input is an input that creates a potential differe...
- FAQ02358 for Safety Relays | OMRON Industrial Auto...
...en there is no reset switch in the feedback circuit and the device automatically starts when an input turns ON. A manual reset is when there is a reset switch in the feedback circuit and the ...
- FAQ02416 for Safety Relays | OMRON Industrial Auto...
... Contents FAQ No. FAQ02416 Related Contents Primary Contents Question What is a positive common input? Answer It is an input mode where there are two inputs and both of them are co...
- faq02041
...nt. Solid-state Relays with a zero cross function using a photocoupler can operate with a small input current because they have very good coupler transmission efficiency. Photocoupler ...
- faq02044
...state Relays Lead Contents FAQ No. FAQ02044 Related Contents Primary Contents Question Does the input current change for Solid-state Relays with a wide rated input voltage? Answer ...
Top of page
OMRON Corporation