... failure to operate, malfunction, or undesirable effects on product performance. !CAUTION Doing so may occasionally result in minor injury due to electric shock. Do not touch the Relay while ...

https://www.fa.omron.co.jp/data_pdf/cat/k8dt-ls_n205-e1_1_8_csm1050141.pdf

...ltage is OFF before starting any wiring work and wire all connections correctly. !CAUTION Doing so may occasionally result in minor injury due to electric shock. Do not touch the Relay while ...

https://www.fa.omron.co.jp/data_pdf/cat/k8dt-ph_n206-e1_1_8_csm1050142.pdf

...et value and measure the time until the Unit operates. Operating Time Adjust the slide resistor so that the voltage applied to the K8DT terminals is 120% of the set value for overvoltage dete...

https://www.fa.omron.co.jp/data_pdf/cat/k8dt-pm_n207-e1_1_9_csm1050143.pdf

... DIP switch setting. Example: K8DT-PZ1 with DIP switch Set to 200 V The rated input is 200 VAC, so the setting range is 10 to 44 V. If you set the setting knob (ASY) to 10%, the asymmetry ope...

https://www.fa.omron.co.jp/data_pdf/cat/k8dt-pz_n208-e1_1_9_csm1050144.pdf

...for general mandatory action precautions for which there is no specified symbol. !CAUTION Doing so may occasionally result in minor injury due to electric shock. Do not touch the Relay while ...

https://www.fa.omron.co.jp/data_pdf/cat/k8dt-th_n209-e1_1_7_csm1050145.pdf

...ltage is OFF before starting any wiring work and wire all connections correctly. !CAUTION Doing so may occasionally result in minor injury due to electric shock. Do not touch the Relay while ...

https://www.fa.omron.co.jp/data_pdf/cat/k8dt-vs_n203-e1_1_8_csm1050139.pdf

...ltage is OFF before starting any wiring work and wire all connections correctly. !CAUTION Doing so may occasionally result in minor injury due to electric shock. Do not touch the Relay while ...

https://www.fa.omron.co.jp/data_pdf/cat/k8dt-vw_n204-e1_1_10_csm1050140.pdf

... following measures to prevent unauthorized access to our products. • Install physical controls so that only authorized personnel can access control/monitor systems and equipment. • Reduce co...

https://www.fa.omron.co.jp/data_pdf/cat/km-pm_n243-e1_1_1_csm1132740.pdf

... power factors to appropriate levels. • Fixed values are used for the voltage and power factor, so the accuracy specifications do not apply. ● Alarm Output An alarm can be output when active ...

https://www.fa.omron.co.jp/data_pdf/cat/km50-c1-flk_ds_e_1_2_csm1039756.pdf

... power factors to appropriate levels. • Fixed values are used for the voltage and power factor, so the accuracy specifications do not apply. zAlarm Output An alarm can be output when active p...

https://www.fa.omron.co.jp/data_pdf/cat/km50-c1-flk_ds_e_2_1_csm1039756.pdf

... into stopped power, standby power, and operating power depending on the power usage conditions so that you can see where energy can be saved. 2) Three-state Energy Classification can be link...

https://www.fa.omron.co.jp/data_pdf/cat/km50-e1-flk_ds_e_1_3_csm1039757.pdf

... into stopped power, standby power, and operating power depending on the power usage conditions so that you can see where energy can be saved. 2) Three-state Energy Classification can be link...

https://www.fa.omron.co.jp/data_pdf/cat/km50-e1-flk_ds_e_2_1_csm1039757.pdf

...A switched and 10 A safe switched are from the same source and pass through the same 10 A fuse, so the sum of their current must be less than 10 A. Auxiliary Power Certification Marking 3.27 ...

https://www.fa.omron.co.jp/data_pdf/cat/ld_i828-e_14_1_csm1056939.pdf

...erate value and the SET knob for the release value. The Relay will normally be ON, however, and so the internal temperature will rise, and this will affect the product service life. 3 LG2 Dim...

https://www.fa.omron.co.jp/data_pdf/cat/lg2_ds_e_4_3_csm388.pdf

...onsider all needed devices when selecting the power supply, camera cables, Ethernet cables, and so on. * □ : 0 = NPN; 5 = PNP FL-BR9120W-H high brightness model, front/side-mount bar light Re...

https://www.fa.omron.co.jp/data_pdf/cat/mx-z2000h_q255-e1_2_3_csm1059279.pdf

...2025/AL2055/AL4025/AL4055/AL4110 Ground terminal (M5) Terminal screw 6-M K D max. E max. W Ro R So S To T W = Terminal width H max. H1 max. X±1 Y±1 A max. C max. Four, J dia. (Cutout) 27 Mult...

https://www.fa.omron.co.jp/data_pdf/cat/mx2-v2_ds_e_4_1_csm1126864.pdf

...6.4 16.5 11.5 形3G3AX-AL2025/AL2055/AL4025/AL4055/AL4110 接地端子 M5 端子ねじ 6-M K D max. E max. W Ro R So S To T W= 端子幅 H max. H1 max. X±1 Y±1 A max. C max. 4-φJ （キリカキ） お問い合わ...

https://www.fa.omron.co.jp/data_pdf/cat/mx2-v2_ds_j_4_1.pdf

... no specifically required installation orientation, but make sure that the Relays are installed so that the contacts are not subjected to vibration or shock in their movement direction. The d...

https://www.fa.omron.co.jp/data_pdf/cat/my_myk_myq_myh_j219-e1_10_25_csm59.pdf

...eries help improving a machine productivity. The NA series features the advanced troubleshooter so that the error details and recovery procedure are displayed on HMI. It also makes a signific...

https://www.fa.omron.co.jp/data_pdf/cat/naseries_v414-e1-01.pdf

...C Input Supply 100 to 240 VAC (allowable: 85 to 264 VAC). The NJ-PA3001 has a wide input range, so it does not have voltage switching terminals. DC Input Supply 24 VDC (allowable: 19.2 to 28....

https://www.fa.omron.co.jp/data_pdf/cat/nj-pa_pd_ds_e_1_5_csm1000600.pdf