GlobalIA Global Search Results
| Site Search | Product Search | IA Global Search |
previous
FAQ02155 for Solid-state Relays | OMRON Industrial......e, the leakage current will increase, so check that the reset failure in item 1 does not occur. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- FAQ02159 for Solid-state Relays | OMRON Industrial...
... to the difference between the SSRs in operating time and reset time when the load is switched. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- FAQ02202 for Solid-state Relays | OMRON Industrial...
...ns with small signal currents. G3VM Solid-state Relay is available from OMRON with NC contacts. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq02211
...to the LOAD or to the INPUT terminal? Answer The load must be connected to the LOAD terminal. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq02235
...210B Solid-state Relays, the following heating value will be obtained. P = 1.6 V x 8 A = 12.8 W MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- FAQ02237 for Solid-state Relays | OMRON Industrial...
...eep the Solid-state Relay ON. Bleeder Resistance 100 VAC 5 to 10 kΩ 3 W 200 VAC 5 to 10 kΩ 15 W MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq02241
...he applied voltage may fluctuate within this range. Voltages outside this range cannot be used. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq03202
...the panel or heat sink. However, by using R99-11 Mounting Brackets, the same pitch can be used. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq03623
...ote:Check the manufacturer’s information for how to connect the overvoltage protection element. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq03628
...elays were mounted to the control panel. (Refer to information on mounting Solid-state Relays.) MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq03629
...ote:Check the manufacturer's information for how to connect the overvoltage protection element. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq03640
...or gang mounting, if the ambient temperature is 50°C, the load current must be kept below 15 A. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- FAQ00871 for Timers | OMRON Industrial Automation
..., the inrush current from the Timer may have damaged the Sensor output. Countermeasure: Use the MY Relay or other relay to turn the Timer power supply ON/OFF. (Make sure that the contact capa...
- faq02579
...grammable Controllers Lead Contents FAQ No. FAQ02579 Related Contents Primary Contents Question My 8-second ON-delay timer program that uses a TIM instruction does not run properly. What is t...
- faq02042
...the NO contacts close before the NC contacts open. These are also called "continuous contacts." MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- FAQ02056 for General Purpose Relays | OMRON Indust...
... contact poles? Answer It is the number of contact circuits, such as two poles or four poles. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq02060
...changeable. Note:These Relays are socket-mounted plug-in type. The Sockets are separately sold. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq02062
...N Relays model number. Specify the coil voltage after the model number as shown in the example. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- FAQ02098 for General Purpose Relays | OMRON Indust...
...table depending on an applied load. Surge protection suitable for the applied load is required. MY Best-selling, general-purpose relays that can be selected based on operating environment and...
- faq02104
...DC Maximum switching current 5 A Contact form DPDT Contact structure Single Contact material Ag MY Best-selling, general-purpose relays that can be selected based on operating environment and...
Top of page
OMRON Corporation