...AC G2RV-ST700/500-AP 230 VAC Note: Voltage is reduced within the socket for the slim I/O relay, so the rated input voltage and rated coil voltage of replacement relays are different. Accessor...

https://www.omron.com.au/products/family/3868/lineup.html

...ld be 1 to 5 mm. Note: 2. To allow easier operation, it is recommended that Adapters be mounted so that the gap between sides with hooks is at least 15 mm (i.e., with the panel cutouts separa...

https://www.omron.com.au/products/family/3899/dimension.html

...tal Filter This function sets the time constant applied to the first-order lag operation filter so that the noise components mixed with the measured value are eliminated. All models Measuring...

https://www.omron.com.au/products/family/3902/specification.html

...nd the wire 4 turns due to the limitation of the wire size,    decrease the number to 3, 2, and so on. When the wire can be wound only a single turn, use 4 or more filters side by    side, wi...

https://www.omron.com.au/products/family/3912/specification.html

... Safety Sensors E3ZS OMRON Non-contact Safety Door Switches D40A-2, D40A Safety Output Units NX-SO Unit type Appearance Specifications Unit version Model Number of safety output points Intern...

https://www.omron.com.au/products/family/3920/lineup.html

...before attempting a megger test (insulation resistance measurement) on a Servo Drive. Not doing so may result in the Servo Drive failure. Do not perform a dielectric strength test on the Serv...

https://www.omron.com.au/products/family/3923/specification.html

...value (peak hold), the bottom value (bottom hold), the range of change (peak-to-peak hold), and so forth. Timer mode Allows you to delay upon changes in judgment output, or turn PASS output O...

https://www.omron.com.au/products/family/3932/specification.html

...rection. (Maintain the specified mounting space between Controllers.) • To mount the Controller so that it is waterproof, insert the waterproof packing onto the Controller. • When two or more...

https://www.omron.com.au/products/family/3937/dimension.html

...rection. (Maintain the specified mounting space between Controllers.) • To mount the Controller so that it is waterproof, insert the waterproof packing onto the Controller. • When two or more...

https://www.omron.com.au/products/family/3938/dimension.html

...A switched and 10 A safe switched are from the same source and pass through the same 10 A fuse, so the sum of their current must be less than 10 A. Standard AMR EN IS0 12100, EN ISO 13849-1, ...

https://www.omron.com.au/products/family/3950/specification.html

...nnector. *3. However, when bending the cable to perform wiring, maintenance, and other work, do so within the temperature range of 0 to 75°C in consideration of severing of the cable. last up...

https://www.omron.com.au/products/family/871/specification.html

...oller. If you reverse this order, this product will       not recognize the 24V external input, so lighting greater than 7.5W will not be possible. *4. Electromagnetic environment: Industrial...

https://www.omron.com.tw/products/family/3279/specification.html

...32, 64 or 96 GB 8, 16, 32, 64 GB Memory type DDR4 (ECC is available) DDR4 Package Memory Format SO-DIMM Serial Presence Detect (SPD) Speed grade 3200 MT/s CAS latency CL17 Trusted platform mo...

https://www.omron.com.tw/products/family/3631/specification.html

... 和 CSA C22.2 No. 61010-2-201 和 CSA C22.2 No. 213） ・FSPC （IEC 61508 和 ISO 13849）＊2 安全I/O模組 NX-SI/SO型 認證機構 標準 TÜV Rheinland *1 ・EN ISO 13849-1 ・EN ISO 13849-2 ・IEC 61508 p...

https://www.omron.com.tw/products/family/3719/specification.html

... If the input is connected to a UPS, do not      connect a UPS with a square-wave output. Doing so will cause the internal temperature of the product to increase,      possibly causing smokin...

https://www.omron.com.tw/products/family/3821/specification.html

...rection. (Maintain the specified mounting space between Controllers.) • To mount the Controller so that it is waterproof, insert the waterproof packing onto the Controller. • When two or more...

https://www.omron.com.vn/products/family/1434/dimension.html

...s, Ltd. --- * There is a risk of quality problems when using cables assembled by typical users, so we recommend purchasing    cables with preattached connectors or having a qualified technici...

https://www.omron.com.vn/products/family/1452/lineup.html

...tch a standard load, it cannot be used for a load of a smaller capacity.                  Doing so may result in roughening of the contact surface and contact reliability may be lost. *1. The...

https://www.omron.com.vn/products/family/1497/specification.html

...tch a standard load, it cannot be used for a load of a smaller capacity.                  Doing so may result in roughening of the contact surface and contact reliability may be lost. *1. The...

https://www.omron.com.vn/products/family/1498/specification.html

...V E39-F1V E32-T84SV 1M (No Cutting) E32-T10V 2M (Free Cutting) E32-VF4 Note 1. Mount the Flange so that the V40 O-ring is on the atmospheric-pressure side of the vacuum chamber wall. Note 2. ...

https://www.omron.com.vn/products/family/1532/dimension.html