GlobalIAグローバル検索結果
| IAグローバル検索 |
前へ
Overview of Code Readers | OMRON Industrial Automa......ndards. When the quality of the barcode printing is not good, the data may be read incorrectly, so it is important to take care in printing labels etc. Features of Barcodes Highly flexibility...
- Overview of Code Readers | OMRON Industrial Automa...
...ndards. When the quality of the barcode printing is not good, the data may be read incorrectly, so it is important to take care in printing labels etc. Features of Barcodes Highly flexibility...
https://www.ia.omron.com/support/guide/349/introduction.html
- further_information.html
...g cable length of 120 meters. This corresponds to a wiring cable length of 150 max. in Table 2, so the maximum length of Sensing Band that can be connected is 150 meters. Example: Parallel Co...
https://www.ia.omron.com/support/guide/48/further_information.html
- Safety Components - CE Marking - Europe, Pan Europ...
...D40A-2 ● D40A *1. Use the D40A-2 and D40A in combination with the G9SX-NS/NSA ,G9SP or NX-SL/SI/SO. Note: Contact your OMRON representative if Applicable Standard No.and Certification Body ar...
- Safety Components - Regulatory Compliance Mark (RC...
...-2*1 ● D40A*1 *1. Use the D40A-2 and D40A in combination with the G9SX-NS/NSA ,G9SP or NX-SL/SI/SO. Note: Contact your OMRON representative if Applicable Standard No. are required. Top of pag...
- Safety Components - UKCA Marking (Machinery, Low-V...
... Not applicable ● D40A*1 *1. Use the D40A in combination with the G9SX-NS/NSA, G9SP or NX-SL/SI/SO. Note: Contact your OMRON representative if Applicable Standard No.and Certification Body ar...
- E8FC IoT Flow Sensors/特長 | OMRON Industrial Automa...
...g position Angle adjustment up to 330° After fastening to the adapter, you can adjust the angle so that the display is easy to see. 180° reverse display The display can rotate 180°. Useful fu...
- E8PC IoT Pressure Sensors/特長 | OMRON Industrial Au...
...ction in processing quality. • The hydraulic pressure system is divided into multiple sections, so finding degraded packing locations takes time. Solution from OMRON You can use a rise in hyd...
- NX-series Safety Controllers / Safety Network Cont...
...ra-high-speed machine automation - Bring safety to your production site Safety I/O Unit NX-SI / SO Build a simple and flexible safety system...
- faq03176
... Possible (except for PCB mounting models) Note: 1.The high level 6 to 24 VDC of H7EC-N is cut, so choose a DC voltage input model. 2.Be careful when using the power-OFF reset. K3HB-X A Proce...
- FAQ02497 for Servomotors / Servo Drivers | OMRON I...
...ontroller with a Pulse Output Problem: Noise is superimposed on the command pulse input signal, so the Driver takes the noise as a command signal. Countermeasures: Separate the power source. ...
- FAQ01122 for Field Networks | OMRON Industrial Aut...
...r The Flange Antennas and Flat Diversity Antennas for the WM30 are designed for the WM30, and so they cannot be used with the WD30. Use the Antennas that are supplied with the WD30. The fol...
- FAQ00846 for Level Switches | OMRON Industrial Aut...
...ause of the problem and how can it be corrected? Answer The following items may be the cause, so check these. Likely Causes A power interruption occurred and the U1 Relay Unit was reset. Th...
- faq00964
...e, use a special E69-DF[] Extension Cable. Do not relay the cable using a terminal block. Doing so will cause the signal to be easily affected by other signal lines. Applicable model combinat...
- FAQ00313 for Photoelectric Sensors | OMRON Industr...
...E32-[][]R) have an allowable bending radius of 1 mm, but do not handle repetitive bending well, so they should not be mounted on movable parts. 2.The light intensity of a Through-beam model i...
- FAQ03372 for Wiring Systems | OMRON Industrial Aut...
...r and the heat sink are attached by hooking them on a claw on the case. There is only one hook, so both devices cannot be attached at the same time. Applicable models: G3S4-A, G3S4-A1, G3S4-D...
- FAQ02469 for Emergency Stop Switches | OMRON Indus...
...require external resistance for the LED? Answer An LED current-limiting resistor is built-in, so internal resistance is not required. F3SR-B For Safety Light Curtain Robust & Basic New Line...
- Download Condition Monitoring Configuration Tool |...
... associated media, printed materials such as manuals, "online" or electronic documentation, and so on. LICENSE AGREEMENT OMRON grants the User a non-exclusive and limited license to use this ...
- CNC Operator downloads | OMRON Industrial Automati...
... associated media, printed materials such as manuals, "online" or electronic documentation, and so on. LICENSE AGREEMENT OMRON grants the User a non-exclusive and limited license to use this ...
- Download H5CC/H7CC replacement time calculation to...
... associated media, printed materials such as manuals, "online" or electronic documentation, and so on. LICENSE AGREEMENT OMRON grants the User a non-exclusive and limited license to use this ...
制御機器商品情報
商品カテゴリ毎の概要・情報。
Top of page
OMRON Corporation