...osition control. SS2 series G5 series Terminal No. Symbol Name Terminal No. Symbol Name CN1 22 +CW/PULS/FA Reverse Pulses Input, Feed Pulses Input, or 90°Phase Difference Pulses (Phase A) CN1...

https://www.omron.com.tw/data_pdf/mnu/i879-e1-01_smartstep2series_to_g5series.pdf

...puts, for Servomotors/Servo Drivers •For stepping motors, combination with basic I/O and pulse (CW) + direction control is possi- ble. Controlling trap- ezoidal position- ing speed control •P...

https://www.omron.com.tw/data_pdf/mnu/o010-e1-01_fqm1-cm001_mmp21_mma21.pdf

...Pulse being output Bit 08 Indicates the direction of virtual pulse currently being output. OFF: CW ON: CCW Bit 07 Indicates whether or not the vir- tual pulse output is being counted internal...

https://www.omron.com.tw/data_pdf/mnu/o011-e1-01_fqm1-cm001_mmp21_mma21.pdf

...86) is used in electronic cam mode (ring), the pulse output can be set to pass through 0 in the CW direction or CCW direction. When PULS(886) is used in electronic cam mode (linear or ring), ...

https://www.omron.com.tw/data_pdf/mnu/o012-e1-03_fqm1-com_mm.pdf

...86) is used in electronic cam mode (ring), the pulse output can be set to pass through 0 in the CW direction or CCW direction. When PULS(886) is used in electronic cam mode (linear or ring), ...

https://www.omron.com.tw/data_pdf/mnu/o013-e1-03_fqm1-com_mm.pdf

...reset Outputs M codes, and interlocks with sequence control program using reset. Spindle ax- is CW, CCW, or OFF Outputs and stops velocity commands in veloci- ty loop control mode. Orientatio...

https://www.omron.com.tw/data_pdf/mnu/o030-e1-07_nj501-5300_ny532-5400.pdf

................................................................................. 3-12 M03 Spindle CW ...............................................................................................

https://www.omron.com.tw/data_pdf/mnu/o031-e1-03_nj501-5300_ny532-5400.pdf

...tating. ORIENTATION Pressing the button rotates the spindle axis to the defined phase position. CW Rotates clockwise. (Default) CCW Rotates counterclockwise. Utilities Function name Descripti...

https://www.omron.com.tw/data_pdf/mnu/o032-e1-03_sysmac-rtnc.pdf

...e direction output is different between the CPM2A and CP1E. Note 3. As the CP1E does not have a CW/CCW mode, change to the system that uses "pulse + direction" mode. CPM2A CP1E-N * CIO CP1E (...

https://www.omron.com.tw/data_pdf/mnu/p084-e1-02_cpm2a_cp1e_replace.pdf

...統仍然不會輸出脈衝。 •利用PULS指令，以絕對脈衝指定的方式來設定移動脈衝量時，由SPED指令的運算元種類所指定的方向(CW方向/CCW方向)就會被忽略。 停止脈衝輸出停止脈衝輸出立即停止立刻停止脈衝輸出。 S...

https://www.omron.com.tw/data_pdf/mnu/sbca-356c-tw5_cp1e.pdf

...l system operation. Components Section 1–2 3 Indicators RUN: indicates operation is in progress CW: indicates controlled system (motor) is revolving clockwise CCW: indicates controlled system...

https://www.omron.com.tw/data_pdf/mnu/w137-e1-04_c200h_nc111.pdf

...elect the start and end ad- dresses, as well as the data to be written. Press the WRITE 2 key. "CW" is displayed in the low- er left corner of the Pro- gramming Console display, indicating th...

https://www.omron.com.tw/data_pdf/mnu/w153-e1-04_c200h-ids.pdf

...DM word m+21 (Y) DM word m+121 00 15 0 0 000 bit Designation 1 0 00 ORIGIN SEARCH direction CCW CW 01 Origin proximity signal presence present absent 02 Origin proximity type N.O. N.C. 03 Ori...

https://www.omron.com.tw/data_pdf/mnu/w166-e1-03_c200h_nc211.pdf

...ON 1 Introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 CW and CCW 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

https://www.omron.com.tw/data_pdf/mnu/w314-e1-01_c200h-mc221.pdf

...r is rotating counterclockwise. g OFF The motor is stopped or rotating counterclockwise. X or Y CW Orange ON The motor is rotating clockwise. g OFF The motor is stopped or rotating clockwise....

https://www.omron.com.tw/data_pdf/mnu/w315-e1-03_c200h-mc221.pdf

...to RS-232C port Connector for I/O Dedicated Terminals (see note 2) External I/O CCW limit input CW limit input Proximity input Immediate stop input General-purpose inputs: 4 pts General-purpo...

https://www.omron.com.tw/data_pdf/mnu/w320-e1-03_cvm1_pro01_v.pdf

...em Configuration 4 1-2 System Configuration The Position Control Unit receives control signals (CW limit, CCW limit, origin, origin proximity, emergency stop, and external interrupt input sig...

https://www.omron.com.tw/data_pdf/mnu/w334-e1-04_c200hw-nc.pdf

...Supported Supported Setting number of unused axes Not supported Not supported Supported Setting CW/CCW pulse output direction Not supported Not supported Supported Setting origin search pat- ...

https://www.omron.com.tw/data_pdf/mnu/w397-e1-10_cj1w-nc.pdf

...and transfer of data, NC Unit monitoring, file management, etc. External inputs CCW limit input CW limit input Origin input Origin proximity input Emergency stop input Interface power supply ...

https://www.omron.com.tw/data_pdf/mnu/w398-01_ws02-nctc1-e.pdf

...71 PT Sensor/ Valve W-series Servo + I/F unit Memory card Max.30 axes (nodes)/total length 50 m CW Limit/CCW Limit Counter DI/O DI/O Pulse output Stepping Computer 5 System Configuration Sect...

https://www.omron.com.tw/data_pdf/mnu/w419-e1-04_cs1w_mch.pdf