...pressure in a range from -400 to 400kPa is applied within 30 seconds, the sensor is not damaged E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01225/

...it is greater than one atmosphere, and "negative pressure" when it is less than one atmosphere. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01238/

...s equivalent to a pressure of 760 mm-Hg expressed by a height of 760 mm on a mercury barometer. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01246/

...between pressure and output voltage? Answer  The relationship is given in the following graph. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01297/

...s. The Pressure Sensor "E8AA Series" can measure it. However, the flow rate cannot be measured. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01299/

... complete absence of air or any objects. It is a condition in which pressure is infinitely low. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01316/

...cm 2 ). How many Pa is 10 kgf/cm 2 ? 1 kgf/cm 2 = 0.0980665 Mpa, so 10 kgf/cm 2 = 0.980665 Mpa. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01327/

...ed, measurement errors and response delays are eliminated, which improves measurement accuracy. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01340/

...le panel and therefore the pressures for four sensors can be controlled from a single location. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01342/

...etting range. In that case, an error message will be displayed for 1 s if teaching is executed. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01347/

...ange is exceeded. For example, the Withstand pressure for E8F2-A01C Pressure Sensor is 400 kPa. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01350/

...oint is 80 kPa, and the OFF is 50 kPa, the hysteresis = 30% according to the following formula. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01443/

...E8M-10 Pressure Sensor is ±1% F.S. Converted to voltage, ±1% × 1⁄100 (%) × 4 V (F.S.) = ±0.04 V E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq01447/

...to 2.00 kPa or 5.00 kPa whether above or below 1 kPa. Indication is not given in units of 1 Pa. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions The zero-reset func...

https://www.ia.omron.com/support/faq/answer/35/faq03426/

...n they are mounted facing each other or in parallel. Model Item M8 M12 M18 M30 DC 2-Wire Models E2E-X[]D[] AC/DC 2-Wire Models E2E-X[]T1 Shielded A 20 30 (20) 50 (30) 100 (50) B 15 2...

https://www.ia.omron.com/support/faq/answer/41/faq00197/

... the sensing object is far and the oscillation level is high when there is a surrounding metal. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What kind of consid...

https://www.ia.omron.com/support/faq/answer/41/faq00201/

...rent frequencies are available to stagger the oscillating frequencies of the Proximity Sensors. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What kind of consid...

https://www.ia.omron.com/support/faq/answer/41/faq00231/

...s? Answer  Refer to the following figures, which apply to Sensor A being affected by Sensor B. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What kind of consid...

https://www.ia.omron.com/support/faq/answer/41/faq00233/

...Question Please teach the principle of operation of Standard cylinder type Proximity Sensor the E2E Series. Answer  The circuit composition and the principle of operation are as follows. 1. ...

https://www.ia.omron.com/support/faq/answer/41/faq00302/

... moving direction of sensing object is parallel to the sensing surface of the proximity sensor. E2E Standard Sensors for Detecting Ferrous Metals under Standard Conditions What kind of consid...

https://www.ia.omron.com/support/faq/answer/41/faq00308/