...id is turned ON. This means that the door will be unlocked if there is a power interruption and so this model cannot be used in systems that would maintain a hazardous state (e.g., systems re...

https://www.fa.omron.co.jp/data_pdf/cat/d4nl_ds_e_9_9_csm1240.pdf

... can be used as unlike poles. * MBB (Make Before Break) contacts have an overlapping structure, so that before the normally closed contact (NC) opens, the normally open contact (NO) closes. 6...

https://www.fa.omron.co.jp/data_pdf/cat/d4ns_d4ns-sk_ds_e_9_9_csm1235.pdf

...tions for Safe Use Do not perform wiring work or touch any terminals with power supplied. Doing so may result in electric shock. Precautions for Correct Use Do not use this product in atmosph...

https://www.fa.omron.co.jp/data_pdf/cat/d7f_ds_e_2_3_csm1772.pdf

...modes that differ by 1 m in cable length. Specifications, however, may not be sufficiently met, so always check operation before actual application. This method cannot be used for the E2C-C20...

https://www.fa.omron.co.jp/data_pdf/cat/e2c_e2c-h_ds_e_9_7_csm445.pdf

... 7 to 11.5 mm set screw (M3) Item A B 20 15 30 12 A *1. Be sure to turn over the braided shield so that none of its thin wires are left. *2. Make sure that an insulation distance of at least ...

https://www.fa.omron.co.jp/data_pdf/cat/e2cy-sd_d112-e1_3_1_csm1000536.pdf

...atings.  Operating Environment 1. Do not install the product in the following locations. Doing so may result in product failure or malfunction. (1) Outdoor locations directly subject to sunl...

https://www.fa.omron.co.jp/data_pdf/cat/e2e-_-il__ds_e_1_2_csm1071692.pdf

...T Proximity Sensor together with the e-jig allows you to easily upgrade your existing equipment so that you can replace the sensor in just 10 seconds. 1. D ismount the M18 proximity sensor fr...

https://www.fa.omron.co.jp/data_pdf/cat/e2e_d120-e1_6_5_csm1059591.pdf

... *2. Refer to page 15 for details. *3. The residual voltage for models without polarity is 5 V, so use caution concerning the connection load interface conditions (e.g., PLC ON voltage). Refe...

https://www.fa.omron.co.jp/data_pdf/cat/e2e_d126-e1-01.pdf

...atings.  Operating Environment 1. Do not install the product in the following locations. Doing so may result in product failure or malfunction. (1) Outdoor locations directly subject to sunl...

https://www.fa.omron.co.jp/data_pdf/cat/e2eq-_-il__ds_e_1_2_csm1071693.pdf

...g on, please use in the stable state. 6. The sensor is adjusted with a high degree of accuracy, so do not use in the environment with sudden temperature change. 7. Operation check is performe...

https://www.fa.omron.co.jp/data_pdf/cat/e2ew-ev_d127-e1_2_1_csm1126893.pdf

...g on, please use in the stable state. 6. The sensor is adjusted with a high degree of accuracy, so do not use in the environment with sudden temperature change. 7. Operation check is performe...

https://www.fa.omron.co.jp/data_pdf/cat/e2ew_d122-e1_7_1_csm1072894.pdf

...unting Parallel Mounting Sensing is enabled within 200 ms for the E2K-C20M@@. Design the system so that the power for the Sensor is turned ON before the power for the load. z Miscellaneous Or...

https://www.fa.omron.co.jp/data_pdf/cat/e2k-c_ds_e_6_5_csm457.pdf

...t change if the cable is extended. Extending the cable, however, will result in a voltage drop, so do not extend the length past 200 m. z Mounting Sensitivity Adjustment Use the included scre...

https://www.fa.omron.co.jp/data_pdf/cat/e2k-f_ds_e_5_7_csm458.pdf

...in operation, however, it is recommended that the E2KQ-X be protected with an appropriate cover so that the E2KQ-X will be free from sprayed water or machining oil. The cable is not coated wi...

https://www.fa.omron.co.jp/data_pdf/cat/e2kq-x_ds_e_4_5_csm461.pdf

...e Use The following precautions must be observed to ensure safe operation of the product. Doing so may cause damage or fire. • Do not install the product in the following locations. (1) Locat...

https://www.fa.omron.co.jp/data_pdf/cat/e2nc_e473-e1_7_1_csm1061200.pdf

...rrect Use Operating Environment 1. Do not install the product in the following locations. Doing so may result in product failure or malfunction. (1) Outdoor locations directly subject to sunl...

https://www.fa.omron.co.jp/data_pdf/cat/e2q6_ds_e_3_1_csm1042712.pdf

... ratings. Operating Environment 1. Do not install the product in the following locations. Doing so may result in product failure or malfunction. (1) Outdoor locations directly subject to sunl...

https://www.fa.omron.co.jp/data_pdf/cat/e2s_ds_e_9_5_csm462.pdf

... N⋅m * If the thickness of the mounting bracket (t) exceeds 5 mm, be sure to install the Sensor so that ℓ ≥ 2, d (dia.) ≥ 45, and D ≥ 2. Mutual Interference When installing Sensors face-to-fa...

https://www.fa.omron.co.jp/data_pdf/cat/e2v_ds_e_3_3_csm1786.pdf

...rture angle Small Spot High Power Narrow view BGS * The optical fiber is 2 m long on each side, so the sensing distance is 4,000 mm. Note 1. The following mode names and response times apply ...

https://www.fa.omron.co.jp/data_pdf/cat/e32-lt_ld_e425-e1_6_1_csm1005701.pdf

...able. The Fiber Unit is not accidentally damaged. Easy Cable Routing The cable opening is wide, so the cable T c can be routed easily. Hex shape Provides Simplicity and Reliability Top-view T...

https://www.fa.omron.co.jp/data_pdf/cat/e32-lt_ld_lr_e437-e1_2_2_csm1017282.pdf