Industrial Automation

Global

Global Navigation

Primary Contents

Site Search Results

Site Search Product Search
Results 631 - 640 of 1179
R88M-1A[] / R88D-1SAN[]-ECT AC Servo System 1S-ser...
... test (insulation resistance measurement)              on a Servo Drive.              Not doing so may result in the Servo Drive failure.              Do not perform a dielectric strength tes...

https://www.ia.omron.com/products/family/3776/specification.html

E3X-ZV / MZV Smart Fiber Amplifier Units/Specifica...
...32-LD11 2M 860 360 250 110 E32-LD11R 2M 840 350 240 100 * The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm. Cylindrical Models Sensing method Size Sensing di...

https://www.ia.omron.com/products/family/3831/specification.html

NX-HTC NX-series Advanced Temperature Control Unit...
...tal Filter This function sets the time constant applied to the first-order lag operation filter so that the noise components mixed with the measured value are eliminated. All models Measuring...

https://www.ia.omron.com/products/family/3902/specification.html

3G3MX2-V2 Multi-function Compact Inverter/Specific...
...nd the wire 4 turns due to the limitation of the wire size,    decrease the number to 3, 2, and so on. When the wire can be wound only a single turn, use 4 or more filters side by    side, wi...

https://www.ia.omron.com/products/family/3912/specification.html

R88D-1SN[]-ECT-51 AC Servo System 1S-series with S...
...before attempting a megger test (insulation resistance measurement) on a Servo Drive. Not doing so may result in the Servo Drive failure. Do not perform a dielectric strength test on the Serv...

https://www.ia.omron.com/products/family/3923/specification.html

ZP-L Laser Displacement Sensor/Specifications | OM...
...value (peak hold), the bottom value (bottom hold), the range of change (peak-to-peak hold), and so forth. Timer mode Allows you to delay upon changes in judgment output, or turn PASS output O...

https://www.ia.omron.com/products/family/3932/specification.html

Further Information of Solid-state Relays | OMRON ...
...quick-break fuse in series with the load as an overcurrent protection measure. Design a circuit so that the protection coordination conditions for the quick-break fuse satisfy the relationshi...

https://www.ia.omron.com/support/guide/18/further_information.html

Further Information of Level Switches | OMRON Indu...
... Note: 2.The circuit configuration of the High-sensitivity 61F-[]H Level Controller is designed so that the relay is reset when there is water present between the electrodes. When power suppl...

https://www.ia.omron.com/support/guide/33/further_information.html

PDFSensors Switches Safety Components Relays Control ...
... high-frequency switching. Unlimited number of switching operations. Consist of semiconductors, so there is no contact erosion caused by switching. Zero cross function. No operation noise. Et...

https://www.ia.omron.com/data_pdf/guide/18/ssr_tg_e_9_12.pdf

PDFSensors Switches Safety Components Relays Control ...
...f the time. (2) Terminal Arrangement •Models with a signal start require three external inputs, so they have many terminals. •Models with a power supply start (H3CR-A8) are the H3CR Timers mo...

https://www.ia.omron.com/data_pdf/guide/19/timer_timeswitch_tg_e_7_5.pdf

Results 631 - 640 of 1179

Related Contents

Site Information

© Copyright OMRON Corporation 2007 - . All Rights Reserved.