GlobalIA Global Search Results
| Site Search | Product Search | IA Global Search |
previous
faq00924...the MOVE DIGITS instruction (MOVD) could have be used, but this time 6 bits have been extracted so the MOVD instruction cannot be used. Instead, the LOGICAL AND instruction (ANDW) will be use...
- faq01011
... No. FAQ01011 Related Contents Primary Contents Question Can I program Programmable Controllers so that all of the outputs in a ladder program step will not turn OFF, even after proceeding to...
- faq01067
...swer The water level signal (1 to 5 VDC) from the Liquid Level Indicator is an analog signal, so first it must be converted into a digital signal using an Analog Input Unit. The following i...
- faq01077
...s The result of the addition operation shown in Figure1 cannot be expressed with only 8 digits, so an overflow (i.e., a “carry”) occurs. In this case the Carry Flag (CY) will turn ON. Figure2...
- faq01464
...Are there instructions that directly make comparisons (e.g., "equal", "less than", "more than") so that comparison results do not have to be accessed from the status of result flags for compa...
- faq02260
...ogramming: CS1/CJ1-series Programmable Controllers Figure 1 The Problem with the Ladder Program So what is the problem with the ladder program? To get to the point, there is a problem in the ...
- faq02639
...rlier than 2.0 or a CX-Programmer version lower than 4.0, individual tasks cannot be protected, so the entire program must be protected instead. CJ2 Introducing the Flagship CJ2 CPU Units, wi...
- faq02836
... (D100) + 123 (constant) = 246 (D100) Note:The instruction in Figure 1 will execute each cycle. So when you want to perform the operation A + B = C in realtime when the add command bit (CIO 0...
- faq02890
...mation. Also, the Memory Card can be removed even when power is being supplied to the CPU Unit, so data can be exchanged with personal computers or spreadsheet software while the Programmable...
- FAQ00198 for Programmable Terminals | OMRON Indust...
...s Question In the NS-series Programmable Terminals, is there a way to create a group of buttons so that all of the other buttons go OFF when one of the buttons is ON (i.e., only 1 button can ...
- FAQ00230 for Programmable Terminals | OMRON Indust...
...ary Contents Question The NS-series Programmable Terminal is not equipped with an RS-422A port, so how can it communicate beyond the rated distance for RS-232C (15 m)? Answer Use an NS-AL00...
- FAQ01111 for Programmable Terminals | OMRON Indust...
...ogrammable Terminal's pin allocation is the same as a Programmable Controller's pin allocation, so use the same cable that is used to connect the computer to a Programmable Controller. The fo...
- FAQ02182 for Basic Switches | OMRON Industrial Aut...
...Countermeasures: Switch the load using a relay or a contactor. A protective circuit is required so that loads such as relays, motors, incandescent bulbs, and solenoids can be used properly. C...
- FAQ02189 for Basic Switches | OMRON Industrial Aut...
...he case and cover, and in Switches. Resistant to gas. The terminal section is exposed, however, so caution is required for water and oil. D2JW Model with Terminals D2SW Model with Terminals D...
- FAQ02231 for Basic Switches | OMRON Industrial Aut...
...gh switching speed shortens the time arcing is maintained. Contact wear and damage are reduced, so stable characteristics can be obtained. Large-capacity switching can be performed with compa...
- faq02946
...gure shows, the Actuator fulcrum is in a different position from that of the standard Switches, so the internal movement is reversed. Even in the free position, the pin plunger is continuousl...
- faq03149
...ches available? Answer There is no definition of high-humidity processing for Basic Switches, so OMRON does not make such switches. Use standard models. 61F-G[]N Improved Design for a More ...
- FAQ03331 for Basic Switches | OMRON Industrial Aut...
...rotary-action operation. Special-purpose Basic Switches are designed for specific applications, so they are limited to use, for example, as power switches for doors. Next, select the maximum ...
- FAQ02105 for Limit Switches | OMRON Industrial Aut...
...tents FAQ No. FAQ02105 Related Contents Primary Contents Question Can WLNJ Limit Switch be used so that a bent coil spring becomes straight after striking the dog? Answer Do not use the WLN...
- faq02122
...is grounded? Answer No, it must be grounded. The socket unit and the lead wire are insulated, so the lead wires must be grounded. 61F-G[]N Improved Design for a More Lightweight Constructio...
Top of page
OMRON Corporation