GlobalIA Global Search Results
| Site Search | Product Search | IA Global Search |
previous
TM S Series OMRON TM Collaborative Robot, S Series......t having to take a robot out of production. The onscreen display includes a virtual robot stick so users can control the robot just as they would control a physical robot. In addition to the ...
- FAQ02275 for Safety Sensors | OMRON Industrial Aut...
...ng Sensors A and B. Adjust where Muting Sensors A and B are installed and the sensing direction so that the passage of a person does not interrupt the beams from both Sensors. F3SR-B For Safe...
- FAQ02323 for Safety Sensors | OMRON Industrial Aut...
...y distance depends on the standards for each country and the standards for individual machines, so always refer to the relevant standards before using machinery. F3SR-B For Safety Light Curta...
- FAQ02328 for Safety Sensors | OMRON Industrial Aut...
...r From a fail safe point of view, Safety Sensors/Safety Light Curtains require to be designed so that a guarded machine will not perform dangerous operation when any malfunction or failure ...
- FAQ02330 for Safety Sensors | OMRON Industrial Aut...
... and F3WN-series, on the other hand, do not have the design features listed under 1 to 4 below, so they cannot be used in safety applications. Main Functions of F3SN/F3SH series 1.The Sensor ...
- faq00886
...rward voltage of the diode must be as low as possible (i.e., 0.1 V maximum with an If of 20 µA) so that the voltage between terminals 3 and 4 will be the specified value of 0.5 V when the res...
- FAQ00898 for Counters | OMRON Industrial Automatio...
...) When using the H7EC-N, the short-circuit residual voltage is 0.5 V max (actual power: 1.0 V), so select a model with a residual voltage (voltage drop when output is turned ON) of 0.5 max, f...
- faq03177
...xternally mounted for PCB mounting models) Note: 1.The high level 6 to 24 VDC of H7ET-N is cut, so choose a DC voltage input model. 2.Be careful when using the power-OFF reset. K3HB-X A Proce...
- FAQ01684 for Servomotors / Servo Drivers | OMRON I...
...or be used in combination with a reduction gear from another company, select the reduction gear so that the loads on the motor shaft (i.e., both the radial and thrust loads) are with the allo...
- FAQ02067 for Thumbwheel Switches | OMRON Industria...
...he advantages to using connectors? Answer The Switch Units can be easily connected and wired, so wiring, maintenance, and inspection are simple. 61F-G[]N Improved Design for a More Lightwei...
- FAQ02416 for Safety Relays | OMRON Industrial Auto...
...re connected to the positive side of the power supply. Both inputs will be at the same voltage, so if there is a short circuit between two terminals, it will not be detected. If there is the ...
- faq02044
...ctor-driven Solid-state Relays, changes in voltage can cause malfunctions in the semiconductor, so be sure to check the actual device before usage. This is not the case for Solid-state Relays...
- faq02064
...ed to be replaced frequently. Power MOS FET Relays have a longer lifetime than other Relays and so the replacement frequency is lower. The terminals of G3RZ Power MOS FET Relays are compatibl...
- FAQ02078 for Solid-state Relays | OMRON Industrial...
...eeder resistance? Answer Bleeder resistance is resistance connected in parallel with the load so that the load current appears to increase in order to correctly switch microloads. MY Best-s...
- FAQ02083 for Solid-state Relays | OMRON Industrial...
...d ON, but the zero cross function causes the load current to always flow from a point near zero so that inrush current can be suppressed more compared to Solid-state Relays that do not have t...
- FAQ02155 for Solid-state Relays | OMRON Industrial...
...measure. Connect a bleeder resistor as in the figure above and set the bleeder resistance value so that the Solid-state Relay input voltage is 0.5 V max. when the Solid-state Relay is OFF. 2....
- FAQ02237 for Solid-state Relays | OMRON Industrial...
...to turn ON, but near point A where there is no current flow the ON status cannot be maintained, so the Solid-state Relay turns OFF and then turns ON when the charge current starts to flow at ...
- FAQ00861 for Timers | OMRON Industrial Automation
.... The power interruption compensation function saves the internal clock data and settings only, so the output circuit remains OFF. K3HB-X A Process Indicator Ideal for Discriminating and Disp...
- faq03033
...100 10S ON The specifications are a power supply voltage of 100 VAC with a 10 s power ON delay, so the replacement product should be the 100 to 240-VAC or 100 to 125-VDC H3CR-A8E. Note:The te...
- FAQ03053 for Timers | OMRON Industrial Automation
...ion for long periods of time (e.g., a month or longer) under high-temperature conditions. Doing so may reduce the life of the Timer due to deterioration of internal parts, such as electrolyti...
Top of page
OMRON Corporation