GlobalIA Global Search Results
| Site Search | Product Search | IA Global Search |
previous
faq01335...ure compensation function makes it easy to set the measurement range. The Sensor is ultrasonic, so it is not affected by the color of objects. Perform a variety of control operations by combi...
- faq01356
...fect E4PA Ultrasonic Sensor? Answer The Ultrasonic Switch uses air as the translation medium, so it is easily affected by wind. Care must be taken when using this Sensor but the E4PA is the...
- faq03137
...ll appear instead of the warming-up display. Warming up itself, however, will not be completed, so high-accuracy measurements will not be possible. Also, ZX-L-N Laser type does not have this ...
- faq03167
...r's Measurement Head of D5V cannot be replaced. The Flat Actuator, D5V[]-3F1, has an M2.5 screw so the Measurement Head can be replaced. Models that have a replaceable Measurement Head are th...
- faq03292
... above 1 μm. Heat rays emitted from the hot object are similar in wavelength to the laser beam, so the receiver element may detect the heat rays. Conduct tests with the actual system to deter...
- FAQ02453 for Emergency Stop Switches | OMRON Indus...
... the Operation Unit or the Socket Unit. The lever has a hole with an inside diameter of 6.5 mm, so the lever can be moved in the specified direction by inserting a screwdriver into the hole a...
- faq02462
...Extractor. 2.Mounting the LED The following figure shows the mounting direction. Insert the LED so that the protrusions on the LED line up with the narrow guides on the socket unit. 3.Mountin...
- FAQ00705 for Digital Panel Indicators | OMRON Indu...
...m/h × (0.006%) = ±0.0051 km/h In this case, three digits are displayed below the decimal point, so the fourth digit below the decimal point in ±0.0051 km/h is rounded off to yield an accuracy...
- FAQ01729 for Measuring / Motor Protective Relays |...
...swer The CT has specific wiring and the Power Sensor has polarity (see Figure 1). Wire the CT so that the load side of the sensing line is on the side of the CT with the label "L" and the p...
- faq03062
...lays operating the instant that an overcurrent is detected. A starting current flows in motors, so Relays do not operate for a certain time during startup and then switches to instantaneous r...
- faq04290
...90 Related Contents Primary Contents Question ZEN Programmable Relays: How do I write a program so that the coil turns ON for only one cycle when the power is turned ON? Answer See the prog...
- faq04299
...99 Related Contents Primary Contents Question ZEN Programmable Relays: How do I write a program so that the coil turns ON for only one cycle when the contact turns OFF? (downward differentiat...
- faq04304
...04 Related Contents Primary Contents Question ZEN Programmable Relays: How do I write a program so that the coil turns ON for only one cycle when the contact turns ON? (upward differentiation...
- faq04305
...put rung of the circuit above, NC contacts of Q0 and Q1 in the second input rung are ON status, so Q0 (forward) and Q1 (reverse) in the first output rung turn ON simultaneously. Programmable ...
- FAQ00675 for Frequency Inverters | OMRON Industria...
...ly converts the input power supply to DC and then converts from the DC power supply back to AC, so differences in the power supply frequency have no effect on operation. CS1W-NC[]71 Decrease ...
- FAQ00684 for Frequency Inverters | OMRON Industria...
...verter with a single-phase 100-V input? Answer No, a single-phase motor cannot be used. Doing so will cause a failure. The Inverter creates a virtual alternating current with high-speed swi...
- FAQ01474 for Frequency Inverters | OMRON Industria...
...hin the Inverter's overload capacity at maximum load. Electronic thermal relays cannot be used, so install a protective thermal relay for each motor. CS1W-NC[]71 Decrease TCO with Simple Oper...
- FH Series Vision System/Features | OMRON Industria...
...eed image storage The amount of inspection image data required for defect cause analysis can be so large that conventional controllers are unable to store it given their storage time and capa...
OMRON Corporation Industrial Automation Company...of PLCs will require a amount of design change works (PLC Programming, unit setting, wiring and so on). Omron will provide repair and maintenance service for seven years after product discont...
https://www.fa.omron.com.cn/upload/alternative/PRDN-2011165E.pdf
- K7DD Application Setting File | OMRON Industrial A...
... associated media, printed materials such as manuals, "online" or electronic documentation, and so on. LICENSE AGREEMENT OMRON grants the User a non-exclusive and limited license to use this ...
https://www.ia.omron.com/product/tool/k7dd/k7dd_app/index.htm
Top of page
OMRON Corporation