...llation Example Cut a thread into the workpiece, and screw in the thermocouple while pushing in so that the tip makes complete contact. Note: E52-CA1DY with the same shape and multiple elemen...

https://www.ia.omron.com/products/family/3151/specification.html

...ll dimensions. Note: With WLHAL4, WL01HAL4, WLHAL5, and WL01HAL5, the actuator's tare is large, so depending on the installation          direction, they may not be properly reset.          A...

https://www.ia.omron.com/products/family/326/dimension.html

...oller. If you reverse this order, this product will       not recognize the 24V external input, so lighting greater than 7.5W will not be possible. *4. Electromagnetic environment: Industrial...

https://www.ia.omron.com/products/family/3279/specification.html

...92F-45 Adapter. To use the USB-                Serial Conversion Cable to make the settings, do so before you mount the Temperature Controller in the panel.           4. You cannot use this A...

https://www.ia.omron.com/products/family/3288/dimension.html

...ng. If the input is 　　connected to a UPS, do not connect a UPS with a square-wave output. Doing so will cause the internal temperature 　　of the product to increase, possibly causing smoki...

https://www.ia.omron.com/products/family/3369/specification.html

...is no place to mount the Top-surface Labels on Two-tier Terminal Blocks with a width of 3.5 mm, so they cannot be used. 3. Use commercially available nameplates (9.5 mm wide, 0.5 mm thick) on...

https://www.ia.omron.com/products/family/3480/lineup.html

...If the input is connected to a UPS, do not connect a UPS with a square-wave output.       Doing so will cause the internal temperature of the product to increase, possibly causing smoking or ...

https://www.ia.omron.com/products/family/3485/specification.html

...ection. (Main-tain the specified mounting space between Controllers.) • To mount the Controller so that it is waterproof, insert the water-proof packing onto the Controller. • When two or mor...

https://www.ia.omron.com/products/family/3668/dimension.html

...irection. (Maintain the specified mounting space between Controllers.) •To mount the Controller so that it is waterproof, insert the waterproof packing onto the Controller. •When two or more ...

https://www.ia.omron.com/products/family/3669/dimension.html

...If the input is connected to a UPS, do not       connect a UPS with a square-wave output. Doing so will cause the internal temperature of the product to increase,       possibly causing smoki...

https://www.ia.omron.com/products/family/3753/specification.html

...mA max. Note: 1. Alarm signal output is not equipped with an internal current limiting circuit, so be sure that the current flowing to the alarm signal output terminals does not exceed 50 mA....

https://www.ia.omron.com/products/family/3780/specification.html

...s should be 1 to 5 mm. 2. To allow easier operation, it is recommended that Adapters be mounted so that the gap between sides with hooks is at least 15 mm (i.e., with the panel cutouts separa...

https://www.ia.omron.com/products/family/3809/dimension.html

...s should be 1 to 5 mm. 2. To allow easier operation, it is recommended that Adapters be mounted so that the gap between sides with hooks is at least 15 mm (i.e., with the panel cutouts separa...

https://www.ia.omron.com/products/family/3810/dimension.html

... If the input is connected to a UPS, do not      connect a UPS with a square-wave output. Doing so will cause the internal temperature of the product to increase,      possibly causing smokin...

https://www.ia.omron.com/products/family/3821/specification.html

...d in continuous or strobed mode. NERLITE Smart Series Lights have a built-in strobe controller, so no external strobe controller is needed. Dedicated cable sets allow you to wire the NERLITE ...

https://www.ia.omron.com/products/family/3847/lineup.html

...AC G2RV-ST700/500-AP 230 VAC Note: Voltage is reduced within the socket for the slim I/O relay, so the rated input voltage and rated coil voltage of replacement relays are different. Accessor...

https://www.ia.omron.com/products/family/3868/lineup.html

...      documents, for faulty wiring can cause failure. Note. Do not connect the shell, for doing so can cause failure or malfunction. last update: October 1, 2024...

https://www.ia.omron.com/products/family/3874/lineup.html

...ation documents, for faulty wiring can cause failure. Note. Do not connect the shell, for doing so can cause failure or malfunction. Note. STC-M[]S502CXP121/-S[]S510CXP62/-M[]S510CXP121/-M[]S...

https://www.ia.omron.com/products/family/3877/lineup.html

...      documents, for faulty wiring can cause failure. Note. Do not connect the shell, for doing so can cause failure or malfunction. last update: October 1, 2024...

https://www.ia.omron.com/products/family/3879/lineup.html

...igE Vision model to FG. Do not connect the shell of the Camera Link or USB3 Vision model. Doing so can cause failure or malfunction. last update: October 1, 2024...

https://www.ia.omron.com/products/family/3882/lineup.html