... hot start is performed when the power supply has been OFF for only a short               time, so in those cases the inrush current values may be higher (as much as two times higher) than th...

https://www.ia.omron.com/products/family/1778/specification.html

...eries Controllers only. *2. Drop-line connections are not supported with a baud rate of 4 Mbps, so Slaves with prewired cables (Bit Slaves)        cannot be used. *3. Round cable, Flat Cable,...

https://www.ia.omron.com/products/family/1779/specification.html

...ns manual startup mode I/O Communications Manual Startup Mode can be set from the CX-Integrater so that remote I/O communications are not started when the power is turned ON.Remote I/O commun...

https://www.ia.omron.com/products/family/1781/specification.html

...model most suited to the application. *3. Set the distance between the Sensor and the Reflector so that it is at least the value in parentheses. Accessories Sensor I/O Connectors (Sockets on ...

https://www.ia.omron.com/products/family/1853/lineup.html

... power ON time.            2. Do not use the Timer with a repeat period of less than 3 s. Doing so may result in abnormal heating or                  burning. Refer to Safety Precautions (H3C...

https://www.ia.omron.com/products/family/1891/specification.html

...d if a hot start is performed when the power supply has been OFF for only a short time,         so in those cases the inrush current values may be higher (as much as two times higher) than th...

https://www.ia.omron.com/products/family/1916/specification.html

...registers for storing PLC memory addresses for indirect addressing. (Index Registers can be set so that they are unique in each task or so that they are shared by all tasks.) Cyclic ...

https://www.ia.omron.com/products/family/2045/specification.html

...llows for repetition of a given operation, start/end of operation data via external inputs, and so on. Accordingly, the PCU can perform various operation sequences without affecting the ladde...

https://www.ia.omron.com/products/family/2051/specification.html

... socket.              When using the short bars on the upper section of the socket, insert them so that their heads are pointed upwards              (see the figure below).              Other...

https://www.ia.omron.com/products/family/2808/lineup.html

... socket.              When using the short bars on the upper section of the socket, insert them so that their heads are pointed upwards              (see the figure below).              Other...

https://www.ia.omron.com/products/family/2809/lineup.html

.... On the model Z-15GQ8-B, the M3 hole with a depth of 10 mm is a through hole. Take precautions so that no                 water or screw lock agent penetrates into the hole. Panel Mount Roll...

https://www.ia.omron.com/products/family/289/dimension.html

... not use both the M12 mounting screw and the mounting holes in the case at the same time. Doing so will cause            stress to be applied to the Switch, possibly damaging the case or cove...

https://www.ia.omron.com/products/family/291/dimension.html

...92F-45 Adapter. To use the USB-                Serial Conversion Cable to make the settings, do so before you mount the Temperature Controller in the panel.           4. You cannot use it tog...

https://www.ia.omron.com/products/family/3101/dimension.html

...llation Example Cut a thread into the workpiece, and screw in the thermocouple while pushing in so that the tip makes complete contact. Note: E52-CA1DY with the same shape and multiple elemen...

https://www.ia.omron.com/products/family/3151/specification.html

...ll dimensions. Note: With WLHAL4, WL01HAL4, WLHAL5, and WL01HAL5, the actuator's tare is large, so depending on the installation          direction, they may not be properly reset.          A...

https://www.ia.omron.com/products/family/326/dimension.html

...oller. If you reverse this order, this product will       not recognize the 24V external input, so lighting greater than 7.5W will not be possible. *4. Electromagnetic environment: Industrial...

https://www.ia.omron.com/products/family/3279/specification.html

...92F-45 Adapter. To use the USB-                Serial Conversion Cable to make the settings, do so before you mount the Temperature Controller in the panel.           4. You cannot use this A...

https://www.ia.omron.com/products/family/3288/dimension.html

...ng. If the input is 　　connected to a UPS, do not connect a UPS with a square-wave output. Doing so will cause the internal temperature 　　of the product to increase, possibly causing smoki...

https://www.ia.omron.com/products/family/3369/specification.html

...is no place to mount the Top-surface Labels on Two-tier Terminal Blocks with a width of 3.5 mm, so they cannot be used. 3. Use commercially available nameplates (9.5 mm wide, 0.5 mm thick) on...

https://www.ia.omron.com/products/family/3480/lineup.html

...If the input is connected to a UPS, do not connect a UPS with a square-wave output.       Doing so will cause the internal temperature of the product to increase, possibly causing smoking or ...

https://www.ia.omron.com/products/family/3485/specification.html